KP3S Print Head With Claw Duct, Stock Fans - V6, Superfly Extruder, Sailfin Extruder, BLTouch/3D Touch
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Remix of (https://www.thingiverse.com/thing:5404993) I remixed this to use the stock v6 cooling and lighten the…
- Ocena
- 0 / 5
- Polubienia
- 18
- Pobrania
- 102
- Wydruki
- 0
- Wyświetlenia
- 2184
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution
Remix of (https://www.thingiverse.com/thing:5404993)
I remixed this to use the stock v6 cooling and lighten the design, yet extremely rigid. I have also added mounting for the Superfly Extruder (you can mount the Superfly in 2 diffrent positions, angled or horizontal). You can use the stock nema 17 extruder motor with the Superfly extruder.
All you need is a $15 BMG Clone, and a few M3 screws/nuts/washers
Superfly Extuder (https://www.thingiverse.com/thing:4914090)
MRF Sailfin Extruder (https://www.thingiverse.com/thing:5149028)
Claw fan duct (thanks to cjlaw1611 - https://cults3d.com/de/benutzer/cjlaw1611 for the design)
It is designed for a V6 hotend (clone) but might work for others as the fan holder is height adjustable.
*Screw list:*
(This list is exact fit)
13 - M3*8
4 - M3 nuts
2 - M3* 30/40 that come with BMG extruder (or clone BMG)
2 - M3/nuts (from stock radial fan)
BLTouch - use the M3 screws and nuts that came with it (M3*8)
Superfly Extruder (6 M3 Washers)
Print head back to X-axis: 4 M3x8
Print head front to back: 2*M3x30 and 2 M3 nuts
Fan holder to print head front: 2* M3x8, 2 M3 nuts
MRF DualDrive Extruder Sailfin to print head: 2*M3x8
Superfly Extruder to print head (2* M3x8, 6 M3 Washers or just use shorter M3's M3*4 or 6)
Claw fan duct to fan holder: 2* M3x8
Endstop trigger to print head back: 1*M3x8
5015 radial fan to fan holder: 2* M3x18 or M3x20 (use stock ones from KP3S)
BLTouch to print head back: 2* M3x8 (use what came with the BLTouch)
*Warning*
Using dual gear extruder (Superfly or Sailfin)
The motor will extrude in reverse (actually pulling filament out)
So using these dual gear extruders you will need to reverse the direction of the of the stepper motor.
I have included a pic of what wires to swap (this is an easy method if you are using stock KP3S firmware) or if you just dont want to compile marlin or klipper. I have included a pic so you can see what wires need to be swapped at the connector of the extruder stepper.
If you do not want to swap the wires, you will need to compile marlin and set the following line in configuration.h:
#define INVERT_E0_DIR true to #define INVERT_E0_DIR false
in the configuration.h
If using Klipper you will need to remove the ! on the extruder pin when compiling Klipper Firmware
*BLTouch offset (nozzle to BLTouch tip):*
X: +25,6 mm
Y: +10 mm
*Superfly & Sailfin E-Steps*
Start with 844 (my exact esteps were 844.8)
easy calculator (https://www.th3dstudio.com/estep-calculator/)
*Print Settings*
Supports:
Yes - only for claw fan
Brim - only for claw fan
40% infill (gyroid) for all parts.
*Notes:*
Everything be printed with PLA(+) depending on how you are using the printer and whether it is enclosed or not.
*Post-Printing*
Tolerances for the mounting holes of the extruders are pretty tight for M3, you might need to use a 3/32 or 7/64 drill bit in the holes to loosen them up a bit. This has been done so you can mount directly into the printhead. Same with the claw fan to the bracket.
*If you want to print Really fast --- > Klipper Configs and Firmware:* https://www.thingiverse.com/thing:5420537
Print Settings
Printer:
Kingroon KP3S
Resolution:
.2
Infill:
40% Gyroid
Filament:
Doesn't matter PLA+
Notes:
Tree supports and brim are only needed for the Claw Fan.
Print all parts in the orientation of the stl
Post-Printing
Some hole tolerances are very tight depending on your filament shrinkage.
You might need to use a 3/32 or 7/64 drill bit (by hand) to loosen the holes for the M3 screws.
They should be a tight fight as some parts such as the extruders don't use capture nuts, and screw directly into the carrier head.
Category: 3D Printer Extruders