1 / 7
Airbus A380 slingshot glider (Only need one elastic band!) — zdjęcie 1
1 / 7

Airbus A380 slingshot glider (Only need one elastic band!)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Orientacyjna cena wydruku pliku

0,88 € – 1,08 € netto (bez VAT)

Dla pliku: A380_Glider_Wingslits_0.1mm_PLA_MINI_1h14m.gcode

To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.

Plik i założenia wyceny

Plik użyty do wyceny

Średnia wycena orientacyjna: 0,98 € netto (środek widełek).

Masa podana przez autora
7 g
Czas druku podany przez autora
1,23 godz.
Materiał u źródła
PLA
Materiał wyceny
PLA
Drukarka wyceny
Bambu Lab P1S - 0.4 nozzle
Proces wyceny
0.20mm Standard

Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.

Zapisane na tym urządzeniu.

This glider has been modelled off of the Airbus A380! fully 3d printable excluding 1 elastic/rubber band.

Ocena
4,5 / 5
Polubienia
211
Pobrania
1329
Wydruki
6
Wyświetlenia
5875
Oceny
6

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Outdoor Toys
Licencja
Creative Commons — Attribution

Hello!

This Glider has been based off the world’s largest passenger plane the Airbus A380-800. 

Both the wing (and body) shape as well as the tail wing/stabiliser are nearly identical to the actual plane however to allow the plane to glide the body of the aircraft has been changed. 

Scaled down to around 1:444 (Wingspan of 79.8m to now 180mm) of the real aircraft.

When making this model I made sure that it would be able to fit my Prusa Minis 180x180x180mm build volume so take care when scaling for larger printers.

 

(You can find the A320 variant glider here: Airbus A320 Slingshot Glider)

 

Printing: 

When printing I would recommend using a layer height of 0.1mm as this stiffens up the wings and also allows for more detail in the wings. I would also use either 0% infill or 5% lightning to lighten the glider. Using these settings will allow the print to finish in just over an hour!

The stick used to launch the plane can be printed at 0.25mm with a high infill (20-25%)

I printed all parts using PLA+ however regular PLA, PETG and ABS would also be suitable.

there are also no supports required!

 

Assembly:

Assembly can be done without glue by just friction fitting however I do recommend a little glue especially on the tail wing.

Attach the rubber band as seen in the bellow photo. 

A picture containing wooden, outdoor, wood, park<p>Description automatically generated"></figure><p><strong> </strong></p><p><strong>Use:</strong></p><p>I would only use this outside as its capable of going quite the distance. if at all you find it veers off to one side adjust by slightly bending the wings until it is stable </p><p> </p><p><strong>Happy Printing : )</strong></p><p> </p><p><strong>P.s.</strong></p><p>For a more stable flight you may want to make the wings <a href=Dihedral by bending a sheet of paper between two objects then placing the plane between. Then, using a hairdryer (or heat gun) carefully heat the plane wings which will mould the gliders wings to the shape of the paper. 

Tagi