1 / 3
Snap-Rotate 2x2 Gridfinity base plate on top of Gridfinity — zdjęcie 1
1 / 3

Snap-Rotate 2x2 Gridfinity base plate on top of Gridfinity

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Put a rotating axis-aligned 2x2 Grid on top of your Gridfinity, for pretty show-casing or switching contexts.

Ocena
0 / 5
Polubienia
49
Pobrania
79
Wydruki
0
Wyświetlenia
1148
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Public Domain

This is a rotatable 2x2 Gridfinity base plate on top of a 608 2RS ball bearing (inside Ø=8mm, outside Ø=22mm, width=7mm) that, using magnets, always snaps to the same orientation of the underlying grid. The rotating base plate requires 3x3 grid of space beneath it, but can also be put on corners to only need 2x2 grid of space beneath it.

Requires at least six or eight 6×1 mm or 6×2 mm magnets, (when using 1mm magnets you can use them singularly or stack them) depending on how much weight you want to put on the rotating plate and how stiff you want the snapping to be.

When putting things on the plate, it should ideally be somewhat balanced for the best rotation experience.

If leaving out the magnets, you have a freely rotatable base plate, which might also have some uses.
 

Sample Video

 

Print Guide


Part GridfinitySnapRotate1 (the base plate) should be printable without supports. (put on the plate, so that the shaft for the bearing prints upwards)

Part GridfinitySnapRotate2 (the rotating 2x2 plate) ideally should have a support in the middle, to help with the large gap for the ball bearing, but can also be printed without it. Put the mostly flat area on the print bed. (holes where the magnets go in are on the print bed)

The press fit for the magnets works well on my printer, but only if printing at regular 100% speed. Avoid printing the magnet holes faster than 100% (I noticed this issue at 300%), since then the magnets might not press fit that well and might require glue and/or drilling. The fast 0.3mm DRAFT mode in PrusaSlicer is fine to use though.

Assembly


Print parts fully - magnets and ball bearing later get pressed into the holes, having a tight fit just from the plastic.

Press a 608 2RS ball bearing into part GridfinitySnapRotate2 (the rotating 2x2 plate), it is unlikely to come out again afterwards. Small holes at the top allow optionally cutting the print open in the future to remove the bearing again.

Using round 6mm magnets with width 1-2mm: put either 2 magnets on the 2x2 plate on opposing sides or fill all 4 magnet slots, depending on desired snap strength, all in the same orientation.

 



Put 4 more magnets into the base plate, all in the same orientation, so that these magnets and the magnets on the 2x2 plate, when it's put on top. Tip for magnet assembly on this part: since the outside is quite narrow and might break when applied too much force, put the magnet in with the outside going in first. The other side you have more contact area to hold the piece and push it in e.g. with a big stick, wrench or any solid thing. This way you have a flat magnet in the end (especially when using 1mm thick magnets) and not one that looks like the one in the bottom right on this picture:
 



Holes for Gridfinity screws and holder magnets have been left from the OpenSCAD model according to specification. Magnets need to be glued in there.

Using magnets or screwing in the modules on top of the 2x2 plate is recommended, since they are subject to sudden impulse forces when starting and stopping rotation.

 

Gridfinity plates based on https://www.printables.com/model/174346-gridfinity-openscad-model 

Tagi