1 / 7
Milwaukee M18 Battery To Harbor Freight Bauer 20V Tools Adapter — zdjęcie 1
1 / 7

Milwaukee M18 Battery To Harbor Freight Bauer 20V Tools Adapter

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Adapts Milwaukee M18 battery packs to Harbor Freight's Bauer 20V cordless tools

Ocena
4,8 / 5
Polubienia
143
Pobrania
720
Wydruki
3
Wyświetlenia
8415
Oceny
5

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial

v3.1 update, 11-April-2024: Finally got to borrow a Bauer 20V battery to take measurements from, and have revamped the design for best fit.  Earlier iterations were functional, but this now fits all the Bauer tools I have to test with just as well as the Bauer battery pack does.  Use the v3.1 top, all other parts are the same.

 

v2.5 update: fixed Bauer side again, to standardize screw length.  All screws now M3x16 flathead. Recommend v2.5 due to the improvements and fine-tuning present over v1 and v2. Latch and M18 battery side are unchanged from v2 but re-upped and re-labeled for consistency.

Updated v2 files available and labeled as such, originals left for historical reasons. Changes/improvements made are: 

Narrowed the terminal block on the Bauer side from 52.5mm to 50.5mm, after finding that that Harbor Freight is inconsistent with the design details and dimensions of the battery slot in their tools. The original width fit well in the tools I had when designing this, but another person making this design discovered it was too wide to fit their heat gun, and I also found it too wide for the brushless oscillating tool.  

Thickened the Bauer side by 2mm in an attempt to standardize all screw lengths at 16mm, failing to realize that doing so makes 16mm screws too short for the latch.  I'll try to fix that with “v2.5” in the next few days.

Chamfered and re-sized the holes for heat-set inserts, as it was discovered the ones I used for modelling have a smaller OD than typical/standard M3 inserts, also added hollow depth beyond the inserts for extra screw clearance.  Re-checked all screw holes for dimensional consistency.  

Enlarged internal channels to more easily fit 14ga wire for additional power handling capacity. I've had no issues with the adapters I built using 16ga wire, but 14ga will give an extra safety margin.

 

Original description:

Adapts Milwaukee M18 battery packs to Harbor Freight Bauer 20V cordless tools. No warranty-voiding tool modifications required, features a 10kΩ resistor in the adapter to fake the thermistor.

The thermistor is a safety feature with lithium batteries to prevent overheating and fire. Do not overly discharge your batteries during use. Not for charging. Do not taunt Happy Fun Ball. Absolutely no warranties expressed or implied. Use this design at your own risk!

i have a number of Milwaukee M18 tools, batteries and chargers. The Bauer tool line from Harbor Freight has some rather nice tools available at an attractive price point, but I have no desire to own and maintain a second battery ecosystem. There are a number of tools either not available from Milwaukee, or that I need infrequently enough that I cannot justify paying Milwaukee prices. There are adapters sold for this on eBay and Amazon, but they cost more than some of the Bauer tools which negates the cost savings. So, I made my own adapters.

Additional parts required:

v1: 
1 M3x16 flathead screw, 4 M3x12 flathead screws

v2: 
1 M3x20 flathead screw, 4 M3x16 flathead screws

v2.5: 
5 M3x16 flathead screws

ALL:
 

5 M3 heatset inserts

2 male 0.250 "quick connect" terminals (interfaces with M18 battery)

3 female Pico 1598D "ATO Fuse Block" terminals (interfaces with Bauer tool)

1 10kΩ resistor, 1/4W-1/2W (there's no appreciable current through this)

wire, solder, epoxy

The Pico terminals need modification to fit the cavities but it's fairly evident what to trim or bend away for clearance on assembly. The connector for the Bauer tool's "TH" terminal is soldered to the 10kΩ resistor, which has the other end soldered to the "-" terminal. Male 0.250" terminals on the M18 side are soldered to the wire and epoxied in place after ensuring they're positioned correctly to mate with the battery. Fishing the wires through the print is a little tricky but not difficult. Longer screw is for the battery latch and sandwiches all parts of the adapter together for strength. I used flat head socket screws since I had them, but any flat head M3 screws will work as long as they're the correct length. Photos taken before applying epoxy to show the resistor bridging the "TH" and "-" terminals.

This is partially based on 05WEL's “Ozito battery to Xfinity (Aldi) battery adaptor” and partially on AgentGene's “M18 to black & decker 18v adapter”. At this point just about all of the sources have been reworked and remodeled, but credit where credit is due.

This adapter also physically fits Harbor Freight's Hercules 20V line, but at least in the impact driver I tested with it didn't allow the tool to work. Your Mileage May Vary.

Print Settings

Printer Brand:

Creality

Printer: 

Ender 3

Rafts:

Doesn't Matter

Supports: 

Yes

Resolution:

0.20mm

Infill: 

20% gyroid, 4 walls

Filament: generic ABS black


 

Notes:

Supports are needed for the long slots where things slide together but were otherwise unnecessary in my experience.

Print the main parts with the sides that mate together against the build plate, and the latching tab on it's side with the screw hole parallel to the build plate. Print latching tab at 999 perimeters or "all walls".

Mine are printed in ABS, but PLA or PETG should work fine too.

Tagi