1 / 6
Dodge Charger Hellcat Style Air Intake Duct for Mopar CAI — zdjęcie 1
1 / 6

Dodge Charger Hellcat Style Air Intake Duct for Mopar CAI

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A duct designed to fit the square opening in the Mopar CAI while still using the same mount and opening as the OEM duct.

Ocena
0 / 5
Polubienia
41
Pobrania
240
Wydruki
0
Wyświetlenia
2656
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

The Daytona edition of the Dodge Charger comes equipped from the factory with the Mopar "cold" (hot) air intake. The air box for this intake has a large hole on the front where a duct for fresh air from the grill would go. However, they don't make a duct that fits this hole and is compatible with the Charger, so they leave the hole open to the engine bay where it sucks in hot air.

While test fitting an earlier design, I noticed an OEM sized duct left a lot of extra space, so I made this duct taller and slightly wider to make the most of the larger opening in the airbox. This did not affect the compatibility with my stock headlights. It was only tested with the headlights that came on my car so if there are other variations, I can't promise it will fit. If you run into this issue, let me know and I can adjust the dimensions and upload a new model.

The extra height does affect which retainer clips fit the mounting hole. The hole itself is the same size but some of the heads are too wide. A clip like the one pictured below is what I ended up using.

Print Settings:

This is a large print (about 313 x 252 x 175) so you will need a printer capable of that. You might be able to split the print in half where the retaining clip goes and use the clip to hold the halves together but I have not tested that. I recommend following the print settings below. Anything less is likely to reduce the longevity of the part. My prototypes used 2 walls with 20% infill and were very flimsy. 

Material: ASA/ABS or other temperature resistant material

  • ASA might better than ABS due to its superior UV resistance. This may not matter since only a small part of the duct is exposed to sunlight.
  • During the summers here in Texas, the air temperature around the airbox regularly exceeds 120°F (50°C) and would get as hot as 175°F (80°C) when the car sitting still for more than a few minutes. Thus PLA is not recommended.
  • PETG should work, depending on your climate, but I did not test it.

Layer height: 0.2mm recommended for the best overhangs. 0.3mm worked but left some rough spots.

Walls: 4

Top/Bottom Layers: 5

Infill: Irrelevant (I had mine set at 40% but with 4 walls, the model was solid anyway)

Orientation: Vertical is highly recommended. 

  • The inside will be the smoothest and it requires significantly less support than printing it horizontally. The least amount of supports will be required with the “back” (where it connects to the airbox) on the bottom.

Supports: Required, NOT included in the STL.

  • Pictured below is how I did my supports for the final print but do as you see fit.

 

Possible revisions:

I'm slowly working on making the interface with the airbox cleaner. The clips on the end don't seem to do much since it's pretty snug. I'm also splitting it into sections that can be snapped together so it can be printed on smaller printers. No promises on a timeline because test fits require removing the front bumper of my car.

 

Edit: As of April 9th 2024, I've had this part installed on my car for 9 months and it's holding up great.

Tagi