1 / 12
Bosch GTS 10 XC // Adapterblock für Federkamm an Parallelanschlag — zdjęcie 1
1 / 12

Bosch GTS 10 XC // Adapterblock für Federkamm an Parallelanschlag

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Adapterblock as fixture of featherboard on parallel slide of Bosch GTS 10 XC table saw

Ocena
0 / 5
Polubienia
25
Pobrania
216
Wydruki
1
Wyświetlenia
2200
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial

hi zusammen :),

ich habe einen Adapter/Aufnahme für einen wie ich finde sehr coolen vorhanden Federkamm entwickelt um diesen unverändert an dem Parallelanschlag (horizontale Anwendung) der GTS 10 XC verwenden zu können.

Anwendungsidee: Exakter und sicherer Zuschnitt von French Cleat Leisten mit 45°.

 

Auf folgende Details wurde speziell geachtet:

  • Höhe des Aufbaus, damit die senkrecht verwendeten M6x80 Schrauben nicht gekürzt werden müssen.
  • Tiefe der Einsteckmuttern für die Fixierung des Federkamms am Adapterblock genau so ausgelegt, dass die Drehknöpfe/Stargrips von der horizontalen “normalen” Anwendung weiterverwendet werden können. (Eine neue lange Nutschiene konstruiere ich gerade noch neu)
  • Die Nuten unten am Adapterblock sind genau so lang, dass die Schraube von oben bei vollem Einschub genau passt :) - Kein hin und her Gesuche notwendig!
  • Die Muttern werden in die Nutsteine eingelegt und überdruckt. Bei den ersten beiden Schichten auf den Metallmuttern muss man bisschen aufpassen evtl. kurz dabei bleiben. Es ist bisschen tricky aber mir gefällt es am Besten wenns “unsichtbar” eingedruckt ist ;D.
  • Natürlich ist kein Umbau an der GTS notwendig.

Hinweis: Ich habe eine gCode-Datei (PETG) für 2Stk. der Nutsteine für den MK3S mit manuellen Treesupports nur an den Ecken und einem Farbwechsel eingefügt. Hier müssen dann die Muttern eingelegt werden. WICHTIG: Messt die Muttern nach, dass die sicher maximal 3,10mm hoch sind. Könnten leicht angeschliffen werden falls ein tick zu hoch → Nicht dass die Nozzle anhaut. Farbe muss natürlich nicht zwingend gewechselt werden.

 

Benötigtes Zusatzmaterial:

  • Sechskantschrauben evtl. Teilgewinde M6x80 (für Befestigung des Adapterblocks in den Nutsteinen am Parallelanschlag)
  • Einsteckmuttern vierkant M6 flach (Kante 10mm - Höhe 3,1mm) (Werden in den Adapterblock eingesteckt)

Unveränderte bestehende Modelle die ich verwendet habe:

  1. “Featherboard for Bosch GTS 10 XC table saw” - https://www.printables.com/de/model/330457-featherboard-for-bosch-gts-10-xc-table-saw
  2. "Handles for M3 to M6 bolts and screws" - M6 Hex Bolt - https://www.printables.com/de/model/359479-handles-for-m3-to-m6-bolts-and-screws

Danke für euer Feedback :)!

Frohes Drucken und Danke für euer Like, wenn euch mein wilder Adapterblock gefällt :)!

 

__________EN____________

Hi everyone! :)

I've developed an adapter/mount for what I believe is a really cool existing featherboard. The purpose is to use this featherboard unaltered on the rip fence (horizontal application) of the GTS 10 XC table saw.

Idea for use: Accurate and secure cutting of French Cleat strips at 45°.

Specific considerations include:

  • Height of the setup, so that the vertically used M6x80 screws don't need to be shortened.
  • Depth of the insert nuts for securing the featherboard to the adapter block, designed to allow continued use of the knobs/stargrips in the horizontal "regular" application. (I'm currently designing a new extended nut rail as well.)
  • The grooves at the bottom of the adapter block are precisely as long as needed for the screw to fit from the top when fully inserted - no need for searching and adjusting!
  • The nuts are placed in the grooves and overmolded. Be a bit cautious during the first two layers on the metal nuts, you might need to keep an eye on it. It's a bit tricky, but I prefer it when it's "invisible" once pressed in ;D.
  • No modification to the GTS is necessary.

Note: I've included a gCode file (PETG) for 2 pieces of the insert nuts for the MK3S, with manual tree supports only at the corners and a color change. Here, the nuts need to be placed. IMPORTANT: Measure the nuts to ensure they're a maximum of 3.10mm in height. They could be slightly sanded if slightly too tall, just to avoid the nozzle hitting them. Of course, changing color is not mandatory.

Additional materials needed:

  • Hexagon screws, possibly partially threaded M6x80 (for attaching the adapter block to the insert nuts on the rip fence)
  • Square insert nuts M6, flat (Edge 10mm - Height 3.1mm) (Inserted into the adapter block)

Unaltered existing models I used:

Thanks for your feedback! :)

Happy printing, and thanks for liking it, if you like it ;D

Tagi