The Schatz Shaker V1: Flexible, Motorized Paint Shaker
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
a paint shaker using the Schatz linkage and a simple "Twist Tighten" holder that allows multiple sizes of paint to shake
- Ocena
- 0 / 5
- Polubienia
- 87
- Pobrania
- 136
- Wydruki
- 1
- Wyświetlenia
- 2850
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution
I don't recommend the use of this anymore, as even the dinkiest of ali-express vortex mixers will do the job better and more elegantly for day to day mixing. this does still have utility for super old paints that need long term shakeage, but that's more niche than most people would suspect.
V2 Eventually.
OLD
--------------------------------------------
The Schatz Shaker is an implementation of the Schatz linkage, shown below.
It's not too complicated to set up, and has minimal non-3d printed components. namely screws, rubber bands, the motor, and bearings.
It shakes. not too complicated. the paint is held in place by two disks holding rubber bands rotating. it's also not too complicated, but pretty cool. This design allows it to hold everything from a Vallejo air paint bottle, to a Vallejo primer bottle. Also, presumably everything between.

PARTS LIST (per component):
UPDATES:
2023-10-22: V2 Motorless shaft still needs a bearing, but is connected via 14mm m4 screw + washers instead! much sturdier when appropriately tightened. Use that instead!
2023-10-21: V2 motor shaft reduces the skateboard bearing count by one, and is better! use that instead of the v1 setup!
Motor: https://www.amazon.ca/dp/B072R57C56?ref=ppx_yo2ov_dt_b_product_details&th=1
Others may work, but that's what I had on hand! Keep in mind the RPM you want may vary based on your control setup, read more below!
- [5x14x5mm Bearings] * 6 (Drum and Swing Arm Bearings)
- [7x22x8 Skateboard Bearings] * 2 (Base Shaft Bearings)
- [50mm rubber bands] * 10
And for Screws: (you don't need all of these, but
- [M3x20mm] * 6 ( Motor Mount)
- [M3x20mm] * 8 ( Top Bracket )
- [M3x16mm] * 8 (Base Arm Supports)
- [M3x12mm] * 4 (Top Plate)
- [M4x14mm] ( Swing Arm Bearing Connects)
- [M3x16mm] * 2 (Swing Arm to Shaft Connections)
- [M3x16mm] * 2 (Shaft to Bearing Connections)
- [M3x16mm] * 4 (Swing Arm Construction)
- [M3x12mm] * 4 (Swing Arm Support)
- [M2x8mm] * 8 (Band connector holder)
The base design doesn't include any control circuitry, nor is the design meant for particular setup beyond the motor! The user is expected to figure that out on their own, but several options are included below!
The Simple Option: (Suggested Motor RPM: 50 (at 12v) or 100 (various!))
Direct Power Supply: You can hook a basic barrel jack up directly to the motor, and have a switch. The motor I used runs @ 100RPM @ 12 volts. This would work best in the 8-10 volts range, as it gets kinda crazy when you run it at full power. Experiment!
L298N Motor Controller: (Suggested Motor RPM: 100)
You can use a l298n motor controller module, of which you can find basically everywhere. The “Base Clamp” is designed in such a way that you can stick a breadboard directly to it (if you get rid of the power rails). Please note that using one of these makes the motor produce a whine if you're not running it at full tilt. Example code is included to control it with a (250k) potentiometer, but, again, I'd experiment with it. There's no mounting hardware included, and whatever you see in the promo video was me either drilling holes for screws, CA glue, or bending spare plastic from a failed print into a bracket to mount a switch.
Example Code:
//pinsint L298N_IN3 = 2;
int L298N_IN4 = 4; //second motor output, what we're using here.
int L298N_ENB = 3;
int MAX_SPEED_THRESHOLD = 430; // Lowest the pot gets
int MIN_SPEED_THRESHOLD = 710; //highest it gets
int MIN_MOTOR_SPEED = 120;//what speed's the minimum before it doesn't work?
int MAX_MOTOR_SPEED = 240;
//max is 255.
void setup() {
Serial.begin(9600);
pinMode(L298N_IN3,OUTPUT);
pinMode(L298N_IN4,OUTPUT);
pinMode(L298N_ENB,OUTPUT);
digitalWrite(L298N_IN3,LOW);
digitalWrite(L298N_IN4,LOW);
digitalWrite(L298N_ENB,LOW);
digitalWrite(L298N_IN3,HIGH);
}
void loop() {
// put your main code here, to run repeatedly:
int potValue = analogRead(A0);
int ScaledResult = map(potValue,MIN_SPEED_THRESHOLD,MAX_SPEED_THRESHOLD,MIN_MOTOR_SPEED,MAX_MOTOR_SPEED);
ScaledResult = min(MAX_MOTOR_SPEED,ScaledResult);
ScaledResult = max(MIN_MOTOR_SPEED,ScaledResult);
analogWrite(L298N_ENB,ScaledResult); //set motor speed
Serial.print(potValue); //can use this to see the high/low values the pot gives out. use this to adjust the min/max respectively.
//if it's backwards, reverse the gnd/5v pins from the pot to invert it
Serial.print(",");
Serial.println(ScaledResult);
}
SPECIAL PRINTING CONSIDERATIONS:
Some parts are too flimsy when printed “Intuitively”
The Shafts (Motor & MotorLess) need to be printed horizontally, hole facing up. Printing them vertically is too flimsy (and even then, the motor shaft is the single most likely part to break during assembly!)

The Base's arms (Both the motor and motorless one!) need to be printed with high infill, they need to be sturdy! this applies to most of the “base” parts. 40% seems to be more than enough.
The Arm's bearing sleeve isn't NEEDED, but reduces rattle a notable amount. it's a bit of a pain to print and assemble.
The fusion files are included, and hopefully will help make assembly easier while I work on a writeup. The bearings aren't modeled, but should be apparent where they are!
Prints that need to be done:
1x of every “base” file (orientate the screw to be up, use tree supports!)
The “Base Arms” need high infill! 40% or more!
1x Main drum (use tree supports, orientate hole up)
4x “Drum Bearing Interface”
2x “Rubber Band Lid Base” and “Rubber Band Lid Cap” - these go on each side of the drum. no glue required!
2x of everything else in “Linkage Arms”
2x “Arm Bearing Sleeve” (Orientate hole up) *(Not mandatory, but nice)
1x “Motorless Shaft”
1x “MotorShaft”
2x “Shaft Arm Mount”
Assembly Considerations:
10 rubber bands are needed. 8 are used as you'd expect, but the other 2 are wrapped around the Band Lid and the drum, as a way to add more traction!
Don't use the old motor shaft! the new one's way sturdier, and saves needing a bearing!
Pulling the bands is a PITA, use a bent piece of coathanger to make it easier!
The bearings should be flush with the smooth surface of things!
Putting the bearing sleeve in the bearing makes it way easier to assemble, as you can line up the holes.