Liczymy pasujące modele…
A spray shaker for drill. You can use it with your drill to shake very well your spray. Is standard but parametric, so you can adapt it if your spray has unusual size. Is for M6 screw (parametric, so you can change it) and the hole is so…
My buddy wanted a salt and pepper shaker holder to go on his side table. It has a mounting point in the center to screw the holder down to his table. On the back side it also has a small clip for him to put notes or letters of importance.…
Holder compatible with a blind shaker up to 74 mm or the original DF64 Metal Coffee Cup. Diameter: Up to 74 mm Attachment: Uses the original screw from the portafilter fork Features: Slot for a 10 x 1 mm magnet at the base Blind Shaker:…
I have closed the shaker in by 2mm either side. Because of this mod, and the fact my toolhead was pushing the shaker back too far, I also extended the shaker arm by 5mm - this allows the Xol to sit back at 0 on the X axis when shaking. I…
Model has approximately 7cm tall and 3,7cm of diameter Printing notes Layer height: 0.12 mm Infill: 25%
Organize your kitchen with this spice rack! Made to fit customizable glass spice shakers (link below), it should also work with most commonly used, square, glass spice shakers with base dimensions of 45x45mm. The spice rack will hold 4…
20x20x45mm velká slánka ze 4 kusů s očkem pro karabinu. Vše se do sebe jen našroubuje. Tisk na MK4, nastavení 0,2mm Ať udělá radost a dobře slouží. :-)
Just a quick print to add a shaker lid to the larger glass ground pepper containers you can buy at Sam's Club. The container lid still fits as well. The shaker lid friction fits with a little pressure. Happy cooking!
If you have Heusingkveld Sprint Pedals and want real ABS feeling, you can get it quite low cost. It's for this bass shaker https://amzn.to/3RGYA0O * to be mounted it needs 6 pcs M8x30 ISO 4762 Bolt 2 pcs M8x45 ISO 4762 Bolt 8 pcs M8 Nut…
This is an orbital shaker with a modular design that employs simple electronics which require minimal soldering skills to assemble. The removable tray has an array of M5 holes into which special mounts can be screwed. Mounts for 125ml and…
I was getting annoyed that my shaker (for the Holy drinks) does not fit inside my car's cup holder. After a while I decided to print it with PETG and 15% infill. Works like a charm and had it for over 2 months now. Also works for other…
Would you like to support my work? :) Check out my full catalog with exclusives, early access and commercial licences. — A small bowl that looks like Spaghetti. It comes with meatball salt and pepper shakers! A cute little addition to…
Paint shaker for miniatures. It's designed to fit Vallejo and citadel botles. --UPDATED-- NEW PRINTING PROFILE (PORTABLE AND RECHARGEABLE) TWO ADDITIONAL PRINTING PROFILES HAVE BEEN ADDED: 1. Base adapted for older wired model, for…
2-in-1 Salt & Pepper Shaker – 3D Printable STL File Add a futuristic touch to your dining experience with this minimalist salt & pepper shaker set, designed by Ürün Atölyesi. With clean lines and ergonomic form, this set is optimized for…
So I was getting fed up of my food being slightly undersalted. but since i am lazy i never got up to fetch the salt. So my answer is magnetic salt shaker. you will need 5mm cubed magnets…
Make the shaker lid with holes smaller, for fine salt Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: Containers
This is a paint shaker for mini paint cans by TESTOR. Designed to shake, not stir, and keep the paint inside the can. Approx. 25mm wide for similar style jars? Adapted to a Theragun style attachment, it should work universally. Use at…
print as oriented. If both models are on the plates, pause at layer 13. The pieces can fit 10mm x 5mm x 2mm magnets and will be 0.3mm off the build plate or 13 layers. i personly plan to spread wild flower seeds around my town where they…
There are commercially available agitators that rotate the developing tank while it lies horizontally on motor‑driven rollers. With this type of system, continuous rotation is mandatory, because part of the film spiral always remains…
Romantic heart model designed for Valentine’s Day. Perfect as a decorative piece or small gift. Designed to be easy to print and suitable for beginners. It can be refilled through the holes in the back (use the caps to close them). 🖨…
LID for a shaker. I printed this in ASA and PETG, then put some cling film under it to make the seal better. note: Most 3d printed parts are not foodsave.
This design inserts directly into the blade holder of a t shank compatible jigsaw. I have only tested it with my cheap jigsaw, so I do not know how it will work with other models. I have used it quite a lot and not experienced much wear…
Have like 5 of those shakers at home but i tend to loose lids/caps so i printed my own. ~40mm in diameter. Enjoy and
Fits shakers made from this website: https://king-shakerz.com/products/king-shaker-personalisieren
An edited version of Patrun's Travel Salt Shaker with a mirrored main body for easier refilling of the salt/spices and a smaller sieve size to screw in perfectly. This way you can just unscrew the bottom and refill, instead of unscrewing…
I printed another design like this, but it fell apart quite quickly. I took inspiration from that design and created this model that is a little more sturdy. I also printed in it in PETG for increased strength. The cans that I need to…
Works with Fanatec CSL Pedals (should work for regular brake, LC brake, and accelerator) and the following 4Ohm 25W Vibration Speaker . Each mount requires (2) M4x0.7x20mm screws and (1) M5x0.8x25mm hex bolt (with an 8mm head width and…
Tired of the little ball rattling around doing absolutely nothing? Meet The Agitator. Built around a standard massage gun head, this fully printable mount shakes your paints properly — none of that polite swirling. Supports AK…
Remove the rubber part from another attachment and put on this. Diameter: 18.5 cm Print the connector_test first to check if it fits your massage gun.
Desk Clamp Protein Shaker Holder A simple and practical 3D printable holder designed to attach your protein shaker to the edge of a desk. It keeps your drink within reach while saving space and reducing the risk of spills. The inner…
It is a salt/pepper shader formed as a sheep. It is hollowed to be filled with salt or pepper, which can be poured of the nose. I've printed a pig salt shaker for my brother and now it gets a sheepy pepper counterpart :) Unfortunately the…
This Minimalistic Salt & Pepper Shaker set is designed to blend seamlessly into modern kitchens while remaining highly functional. Each shaker features a simple cylindrical form, measuring 86 mm in height and 30 mm in diameter , offering…
SIMPLE SHAKER XL A shaker for salt, pepper, MSG, herb mixtures and other things that can hold 500g / 1.1lb of salt. Printable without supports. Allows for closing and also offers small holes (2mm diameter), large holes (3.5mm diameter)…
Drill guide / jig to install cabinet pull knobs on "slim shaker" style cabinetry with a 3/4" frame. This drill guide works for upper or lower cabinets and places the knob 1" from the side of the frame and 1.5" up/down from the frame;…
Salt and Pepper Shaker with Handle A simple salt and pepper shaker with a handle that is easy to print and can also be customized afterwards. I printed and tested the model myself successfully. Files Included are: a 3MF file for direct…
A clamp to mount 50 mL tubes to an orbital shaker. The tube fits snugly in the bottom clamp, the cap sinks into a divot so the rim is prevented from moving while the shaker is in motion. The top clamp clips around the back of the bottom…
A clamp to mount 50 mL tubes to an orbital shaker. The tube fits snugly in the bottom clamp, the cap sinks into a divot so the rim is prevented from moving while the shaker is in motion. The bottom clamp screws into the shaker platform…
lids for shaker with inner diameter ∅40mm (∅id39.8mm) ∅3,∅4 and ∅5 hex-holes (parametric script)
Nalgene bottle shaker insert This insert fits in a classic (wide opening) Nalgene water bottle. It allows using your Nalgene for powder drinks (e.g. protein shakes) and turn it into a shaker bottle 😎 Printing instructions The model can be…
Used Akaziuna's Skull with Pointed Teeth to make a little dice holding shaker skull. I printed the Skull at .596465 scale (to fit my printer) and then measured the bottom of it to make the plug for the bottom. Print it at big or as small…
Massage gun holder for Craft Smart 2 fl oz (59 ml) paint bottles for use with RAEMAO Massage Gun. Modified version of the 2oz_shaker by Zimlorog. The length was extended to fit a Craft Smart Bottle and end was adapted to work with a…
Oh boy. These marks are all over the place now! I made this salt shaker compatible stencil to make little gnome shoe prints. This is much easier and on the spot than other stencils I tried. The grid is just the infill pattern without top…
Size 80x80x87 Printing of the first layer thickness 0.28 width 0.6 then thickness 0.2 width 0.4 Fuzzy shell up to a height of 80.08 mm On the lid, the thickness and width are the same, the first layer is a spiral octogram, the last is…
Created a small shaker lid to convert a pill bottle to a camping salt shaker.
It just dumped a ton of snow on us, and I don't have anything to spread the snow melt with. Thankfully, I do have a 3d printer and some menial CAD skills. So here's my take on a giant salt shaker meant for snow melt. Super easy print,…
The Rhino Horn is a cheap and simple but pretty efficient nose cleansing tool. Using it requires adding the right salt concentration to water at body temperature. In order to do so, the Rhino Horn ships with a measuring spoon. But this is…
The Donut Espresso Shaker is an espresso shaker that enables even distribution when preparing espresso for a wide range of portafilter sizes. What makes the Donut Shaker special is that it achieves this result with any portafilter size…
Originally designed by Guido van Hout, slightly remodelled with coarser threads and chamfered inside/outside to reduce overhang and seam size. Also increased size and added slotted hole. Note, while printing I had some internal strings…
I wantet it to shake more, so i went for a vertical shake. Fits bottles from Vallejo and Army Painter and the like.
Object description: This is an insert for a Fuchs pepper shaker. The model includes a 0,4mm thick support layer which should be printed in a different material as the main part. It is divided into two halves to make it easier to remove.…
A simple wand that is also a salt shaker. It can cause a lot of laughter during a family dinner in the hands of a grown
If you want to empty a barrel etc using a siphon but find it uneasy to start the siphon - this is an easy way to do so. This shaker siphon is a actually just a valve. By shaking it down into the water (or other liquid), that water can…
Get your lids in order and organize that cabinet! This lid organizer is a practical solution for decluttering your kitchen. The compact design can hold 4-5 lids stacked upright on the vertical pole.
This is for carrying on a motorcycle. It's flow rate is rather low of course, but when one needs to transfer a bit of fuel to a friend, then it's going to be invaluable. It takes way less space than a spare fuel container. I drilled and…
A handy canister with some holes so it can function as a shaker! Fill it with magnesium/chalk powder for grippy hands anywhere you need it. Could be used for salt or pepper as well to spice things up 😉 Print instructions: Can be printer…
I needed to build a bunch of shaker-style cabinet doors, which of course requires a lot of lining up, gluing, and clamping. To make things easier, I made a right-angle jig that can help hold the boards in proper alignment both for a dry…
Made as a birthday gift. The model consist out of two parts, these can be assembled and fixed together by a m2x8 bolt and m2 nut.
Hello there, please see my Multicolor Rocket, which can be used as a Salt Shaker STL contains two parts Top-part can be screwed on and Salt can be inserted whith the orange “flames” on the bottom you need to be a bit creative, I just…
Pair of salt and pepper shakers designed to mesh together and turn as gears upon their stand. The bottom is threaded to fill the shakers. Enjoy and happy printing! :-)
Material PLA+ Layerhöhe 0,15 mm (erste Schicht 0,25) Infill 100 % Support 0% Im Griffstück habe ich zur Verstärkung einen Metalldraht Ø2mm eingesetzt. Gutes Gelingen und über ein Like würde ich mich freuen. Good luck and I would be happy…
most basic salt pepper shaker with storage container for multiple shakers in pattern of honeycombs. Also with optional handlebar which you can simply glue on I recommend definitely scaling all objects up since it is pretty small, I was…
Introducing the Connectable Salt and Pepper Shakers with screw-on tops, a perfect kitchen duo designed for convenience and style! These two shakers can be connected side by side or one over the other, keeping your salt and pepper within…
This machine is designed for Jobo 1520 film development tanks. Additionally to the printed parts you need: 1x power supply - 24V / 6A (or what your motor needs) 1x nema 23 stepper Motor 3nm 1x nema 23 motor l-mount 1x motor mount 8mm 1x…
Print in any rigid material, I used PLA. No support is needed. You can generate lids for most any shaker if you used Fusion 360 and modify the Outside_Diameter parameter (SOLID toolbar section >> MODIFY >> Change Parameters), with the…
Two models are provided. One for standard (large) spray cans and one for smaller Humbrol type cans. For both, spring fingers accomodate slight variations in size and hold cans firmly in place. Model is designed to use 8mm coach bolt as…
This is a remix to fit my chinese Massage Gun, it as a ~13mm cilinder.
I thought the available shaker boxes were a bit steep pricewise and also very crammed for my big fingers. It started with the idea of a somewhat wider grid for convinience and escalated from there into a modular box system when I figured…
V3 UPDATE 11/12/24: Added reinforcement across the whole lip. ------------------------------------------------------------------------------------------- V2 UPDATE 25/10/24: Due to excessive clatter on the 8020 profile, I've added a…
Allows for mounting an Aurasound or Dayton Audio bass shaker on extruded aluminum. My shakers have holes for M5 bolts, and I used M5 heat set inserts to hold them in place to the mount. I've included STLs for both M5 and M4 shaker mounts,…
Stand to hold a blind shaker beneath a Option-O Lagom Mini instead of the original catch cup
The mount is designed to be attached to Aluminum extrusion profile 4040 via couple of M6x20 bolts (18mm M6 washer recommended), 4080 via 4 M6x16 inbus bolts or under Fanatec CSL Pedals, directly under brake pedal via couple of M4x40. 2 M4…
Adapter that makes it easy to transfer the coffee from the shaker to the portafilter without spillage. Use it together with my or a similar tamping station
A spray shaker for drill. You can use it with your drill to shake very well your spray. Is standard but parametric, so you can adapt it if your spray has unusual size. Is for M6 screw (parametric, so you can change it) and the hole is so…
This can be mounted on profile extrusion 40x80 Holes for M6 screws. For the bass shakers , use m4 and threaded insert or just m4 nuts.
Some prototype Rhythm Bones I designed in TinkerCAD, and a version with a shaker attachment! I made the shaker a separate file so it can be printed in a different material if you want. Just wait till the shaker is roughly halfway finished…
thes salt and pepper shakers fetchers snas as the salt and pappyrus as the pepper
My buddy wanted a salt and pepper shaker holder to go on his side table. It has a mounting point in the center to screw the holder down to his table. On the back side it also has a small clip for him to put notes or letters of importance.…
Designed this to allow for mounting of 100mm bolt pattern bass shakers, like Dayton Audio BST-1, to NRG bucket seats without the need for drilling. This mount takes advantage of the seat bottom harness pass-through hole. Tolerances allow…
Hi, this is a simple shaker with a thread which works just fine. great thing: you don’t need any support print with: 0.2mm 40-50mm/s worked fine Please download and try it out and thx for any “likes” or productive comments! Have fun! ;)…
Hi, this is a simple shaker with a thread which works just fine. great thing: you don’t need any support print with: 0.2mm 40-50mm/s worked fine infill: 20% it’s a bit massive, so maybe i’ll update that model in the future. Please…
Tired of fumbling with those tiny packets of salt and pepper? This is the answer. Stick the holder-holder on your dashboard or desk and put a packet in the holder. Tear off the corner as usual and tap the holder to control the output.…
Holes in cup 2mm(H) 2,5mm(I) and 3mm(J). Jars diameter cca 40mm, volume cca 80-90ml. Walls thickness 2mm. For salt recomended J2 cup, for pepper H2. Filament need for shaker (jar with cup) cca 12m. Tested PLA 0,2mm, random seam. Spice…
Holes in cup 2mm(H) 2,5mm(I) and 3mm(J). Jars diameter cca 40mm, volume cca 80-90ml. Walls thickness 2mm. For salt recomended J2 cup, for pepper H2. Filament need for shaker (jar with cup) cca 12m. Tested PLA 0,2mm, random seam. Spice…
place a rubber between the shaking parts. Don't glue those parts together. It will work at 3 to 9 volts
This is an adapter I created to stop my blind shaker from moving around on my Eureka Mignon Oro metal stopper during the grind process. Made for 58mm portafilter version.
Hello everyone! I designed these 3D-printed supports for 30 mm diameter springs, intended to isolate the seat, enhance the performance of the bass shakers, and minimize vibration transfer to the rest of the simulator. The 3D support…
If you are a weird coffee person who likes espresso, you are aware that shaking your grounds is all the rage. If you use a Niche Zero grinder and don't want to sink the money on a fancy Blind Shaker, this is a very cheap alternative. Drop…
salt and pepper shaker put salt in one side pepper in other twist to open and close
This sugar shaker always dispenses between 2.4-2.5g, down to the last crumb. For printing I used Pla, for the container no support is needed for the lid maybe wel. The nice detail is that it is always between 2,4 en 2,5g till it is…
The original lid is broken, but the shaker is still fine? Print yourself a new lid. I recommend using TPU, I printed this lid with Bambu TPU for AMS with a shore hardness of 68D and it works fine: noozle 0.6mm 0,18 mm layer 3 wall loops…
Holder compatible with a blind shaker up to 74 mm or the original DF64 Metal Coffee Cup. Diameter: Up to 74 mm Attachment: Uses the original screw from the portafilter fork Features: Slot for a 10 x 1 mm magnet at the base Blind Shaker:…
