Smooth Spinning Spirographic WDT for 54mm & 58mm Portafilters
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Bearing-Based Spirographic WDT that only needs a single finger to operate. Compatible with 58mm and 54mm Portafilters
- Ocena
- 4,833 / 5
- Polubienia
- 75
- Pobrania
- 479
- Wydruki
- 8
- Wyświetlenia
- 4911
- Oceny
- 6
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Noncommercial
WDT (Weiss Distribution Technique) is a method of espresso preparation to evenly distribute coffee grounds in a portafilter to ensure a more even extraction of coffee from the espresso machine.
This tool uses several needles spinning in a spirograph pattern to evenly distribute the coffee grounds in a portafilter in a smooth, easy-to-operate fashion.
Redesigned Spirographic WDT from Kensei and Ungodly's designs to reduce the number of additional parts needed to purchase, make it shorter, make it more functional, and make it easier to print.
Additional Parts Needed
- 1x Large Ball Bearing:
- 58mm Version ONLY - Part # 6813 Ball Bearing (85mm OD, 65mm ID, 10mm Thick)
- 54mm Version ONLY - Part # 6812 Ball Bearing (78mm OD, 60mm UDm 10mm Thick)
- About $10 for one bearing. For either of these bearings, I recommend a non-sealed bearing to get it to spin freely like a fidget spinner, or removing the seal on a sealed bearing and soaking it in Naptha/mineral spirits to remove the thick/heavy grease. Add a drop of light grease like machine oil to keep it from rusting.
- Use the Bearing Press 3D printed part to push this down into the top piece. It's a very tight fit. I used a dead below hammer to press it into place, but you can use a regular hammer or clamp to press it into place
- 4x Mini Ball Bearings:
- Part # MR63ZZ Ball Bearings (3mm ID x 6mm OD x 2.5mm Thickness)
- A pack of 10 is around $9
- Use a clamp to press these into the 3D printed gears
- 4x M3x12 Screws:
- A big assortment pack of various M3 screws sizes is about $10.
- When screwing the gears down, do it slowly, and check to top side of the top part as you're screwing it in. If you start going too deep, it will start to push through the top. I tapped this hole with a M3 tap, but you can get away with not doing it.
- Also spin the gears after putting the screws in to make sure they can still spin freely. Otherwise back it out a little.
- 10x 3D Printer Nozzle Cleaning / Accupunture / WDT Needles with 1.4mm Handles
- A pack of 50-60 of these is about $7
- You'll need to trim the handle down to about 15mm, and then put a slight bend in the middle of the handle so that it holds snug in the holes of the gear
- Trim down the needle so that it fits into your portafilter. There's too many different baskets/portafilter combinations out there for me to say what size you need
- Make one needle on each gear 10mm shorter than the others in order to improve distribution. These shorter ones will rake across the top instead of the bottom like the others.
OTHER TIPS
- Test fit the how the gears mesh together after you screw them in for the first time. Do this by placing them on the lower body without the bearing in place. You'll be able to see if it spins nicely, or you might need to sand down any minor imperfections on the gear faces to get it to spin cleanly.
- I used wood PLA, which I sanded and stained with Java Colored Gel Stain. This gave the entire thing a much more wood-like premium look to it.
- I highly recommend you seal the lower body lug part with epoxy or polyurethane to make it food-safe since it will touch your portafilter and the coffee grinds. Seal the gears too so they don't shave plastic into your coffee.