1 / 19
MMU3 / MMU2S  5 Spools auto rewinder adapter for (un)original Prusa drybox / Repbox — zdjęcie 1
1 / 19

MMU3 / MMU2S 5 Spools auto rewinder adapter for (un)original Prusa drybox / Repbox

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

5 Spools rewinder adapter for MMU2S / MMU3 in (un)original Prusa drybox or Repbox. Could be used without drybox

Ocena
4,952 / 5
Polubienia
971
Pobrania
3304
Wydruki
139
Wyświetlenia
28 861
Oceny
125

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is an upgrade for users of MMU and who has (un)original drybox (also works with the Slim version). This system replaces the filament buffers.

It's a project in development that I try to improve with the time, thanks for your understanding.

And thanks for your support 😉

 

I thinking this project to be the most useful possible :

  • Easy access for changing your spools
  • Auto rewinder because it's a most elegants solution than the buffer (personal opinion 😉)
  • Shorty path as possible to avoid a maximum of friction
  • Preservation of the opening from above for mmu maintenance 
  • Beam A1 mod  and Beam A2 mod :

Those parts replace back parts Bean A1 A2 on the (un)original drybox. 

 

  • There are 5 spool with auto-rewinding remix  (Original by Jim Nangano )
  •  New guide ptfe in the drybox systeme (made by myself)

PTFE connector for MMU3 owner :

For my full MMU systeme (with the two link in the bottom) you need some PTFE tubes : 

The MMU3 come with (10 X 60 cm PTFE) tubes so I created this connector for use them, the clips used for maintain the ptfe tubes come also with the MMU3.

 

If you don't use a MMU3 kit you need about 4 meters ID=2,5mm OD=4mm  : (These size are with a slack )

  • 2 X 85 cm
  • 2 X 80 cm
  • 1 X 70 cm  

I advice to buy 5 meters to be sure and cut off the excess once installed.

 

You needed some non printable parts :

  •  screw M3x10 X20
  •  608 bearings X10

 

Be careful to build correctly your rewinder, the axle must be placed last. Put it in starting by the lid like on the bottom photo. ( thanks to @HonzaJaros_1717380 for help with this issue)

 

All parts were printed with PETG Prusament  during testing.

Print the rewinder system in ASA if you use the heater for (un)original drybox.

 

I also do a fixation for the (un)original drybox on the Prusa enclosure  :

https://www.printables.com/model/702384-fixation-for-unoriginal-prusa-drybox-on-the-prusa-

Fixation for Core One :

https://www.printables.com/model/1375957-unoriginal-holder-for-core-one

Pass Ptfe on the top of enclosure  :

https://www.printables.com/model/702362-guide-ptfe-mmu-top-on-prusa-enclosure

 

You can look at this complet guide created by FuseFox Design to build the system:

https://www.printables.com/model/1126694-fusebox-build-guide-mk4s-wmmu3

 

Tagi