1 / 8
Weighted Wheels for Axial AX24 (1/24 AX24 XC-1 4WS CRAWLER) — zdjęcie 1
1 / 8

Weighted Wheels for Axial AX24 (1/24 AX24 XC-1 4WS CRAWLER)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Weighted Wheels for Axial AX24 (1/24 AX24 XC-1 4WS CRAWLER) & Maybe other crawlers The weight added comes from Washers.

Ocena
0 / 5
Polubienia
20
Pobrania
79
Wydruki
0
Wyświetlenia
1190
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Weighted Wheels for Axial AX24 (1/24 AX24 XC-1 4WS CRAWLER)

(This may work on SCX24s and similar sized crawlers but I have only tested it on an AX24)


The weight added comes from Washers slid onto the part "Wheel Hub Main" before gluing on part "Wheel Hub Main - Glue On Plate".

I have tested this with the original tires that come with the AX24 and it works fine with them. Other tires may have different sizes and thicknesses and require adjustment to fit them.

Mounting them to the car works by inserting a 4mm hex socket with the wheel nut slid into it first, down the center shaft of the wheel hub. - This sounds and seemed more finnicky than it really is.

 

Washers used are following the standard DIN 9021.
Inner hole diameter: ca 10.5mm
Outer diameter: ca 30mm
Thickness: ca 2.4mm
Weight per washer: ca 10.4g

I currently run 5 washers per front wheel and 4 per rear wheel, so roughly 52g per front wheel and 42g per rear wheel

Total material cost comes out to 10-12 USD.
I was able to buy 2x10 washers for roughly 10 USD.
Plastic is roughly 7-9g/wheel - one "Hub Cap" and the optional "Inner Tire Shape Retainer Plate" included, so a rough total of 40g for all 4 wheel hubs.

 

Required Parts to print & amount of them (Per Wheel):
Amount | Part Name:
1 | Wheel Hub Main
1 | Wheel Hub Main - Glue On Plate
2 | Tire Lock Plate


Optional Parts to print & amount of them (Per Wheel)::
Amount | Part Name:
1 | Inner Tire Shape Retainer Plate
1 | Hub Cap - Design 3
1 | Hub Cap - Design 1
1 | Hub Cap - Design 2


Assembly instructions assuming you printed the following:
1 | Wheel Hub Main
1 | Wheel Hub Main - Glue On Plate
2 | Tire Lock Plate 
1 | Inner Tire Shape Retainer Plate

See pictures if any of the steps below are unclear.

Step 1) Slide 4 or 5 washers onto the center of "Wheel Hub Main". (I added some super glue between the washers and between the washers and the plastic to prevent them from spnning and rattling.)

Step 2) Glue on "Wheel Hub Main - Glue On Plate" onto the "Wheel Hub Main" to secure the washers between the sides of the "Wheel Hub".

Step 3) Slide the "Wheel hub" inside the tire so that the tires rubber is now on the outsides of the Wheel hub sides.

Step 4) 
--This step requires clamps or that you are prepared to hold parts pushing down hard until the glue has properly cured--
Apply super glue to the wheel hub part visible in the center of the tire and onto the part 
"Tire Lock Plate", insert the smaller diameter side of "Tire Lock Plate" into the center of the wheel hub making sure that the holes of the parts line up so that you later can screw the tire onto your car.

Step 5) Repeat step 4 for the other side of the wheel hub.

Step 6) --This step is optional--
After the glue from step 4 & 5 has properly cured, now glue the part "Inner Tire Shape Retainer Plate" on the inner "Tire Lock Plate" so that it pushes the tire out and away from the side towards the car.

 

Tagi