1 / 2
Ender 3 V3 (non SE/KE) Filament Guide for use with Dryer Box (Rev.3) *UPDATE 5/27* — zdjęcie 1
1 / 2

Ender 3 V3 (non SE/KE) Filament Guide for use with Dryer Box (Rev.3) *UPDATE 5/27*

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Filament Guide to use with Dryer Box

Ocena
0 / 5
Polubienia
31
Pobrania
188
Wydruki
0
Wyświetlenia
3986
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

*UPDATE 5/27/24* 
The very first 3v3 I got when it first came out had 2 M4 threaded holes on top of the gantry. I bought a second 3v3 about 2 weeks ago and it did not come with those holes. My new recommendation if you receive a 3v3 with no threaded holes on top of the gantry is to simply adapt a drybox with a PC4-M6 fitting to a PTFE tube and feed that tube over to the original mounting position of the runout sensor, replacing the small tube that comes installed on the runout sensor.

Filament Guide for the brand new Ender 3 V3 (non SE/KE) 

To complete this after printing these parts, you will need:

1x Ender 3 V3 SE/KE Filament Runout Sensor Mount 
    - The spool holder screws that come with this package will also be needed, or you can source your own, they are M4.
    - I also used the stock runout sensor that comes with the V3 non SE/KE, but I don't believe you have to. The sensor that comes with this package is smaller, so it'll be personal preference which to use.
    - You can buy this package from Amazon here:
https://www.amazon.com/gp/product/B0CP5TL417/ref=ox_sc_act_title_2?smid=AZ11IMTFYQFYA&psc=1


2x 8x22x7 608ZZ Bearing
    - https://www.amazon.com/gp/product/B07216D1SZ/ref=ox_sc_act_title_1?smid=A3DDYVJT6VP8R&psc=1

1x 3 Pin JST XH 2.54mm Connector Cable (I had to use 2x) 
*(No Longer Needed with Rev.3)
    - Use this to extend the sensor cable all the way up. I had to use 2 of them since mine were short.
   - https://www.amazon.com/gp/product/B08PSDLL8H/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1


3x M4 x 12mm screw to mount the runout sensor and the guide.

2x M3 x 25mm screw, 4x Washers, 2x Nuts to mount the rollers.
 
1x Gaffers Tape (or any tape, or whatever other solution works for you) 
*(No Longer Needed with Rev.3)
    - To secure the runout sensor cable to the vertical part of the gantry. Gaffers tape is pretty good and doesn't leave residue (unless it's really old or low quality).

---

3/17/2024 (Revision 3): Lowered the runout sensor, now you do not need to extend the cable for it. Also added a second roller. This design has the least friction I have tested thus far.

Edit 3/14/2024: I have discovered 2 things about using this that could help or at least prevent potential issues.

1) In order to help keep the filament from bending at extreme angles into the extruder when it's homing at the top of the gantry, I cut a piece of the teflon tube included with this printer and added it to the extruder, see Pic 2.

2) At the end of a print, to help prevent the same issue as above but at the end of a print, you can go into the Configuration page in the Fluidd interface, open gcode_macro.cfg, scroll down to [gcode_macro END_PRINT]. Toward the bottom of this macro, you can see it calls to another macro named END_PRINT_POINT, which at the end of a print lifts the extruder to the top of the gantry. Well there is a second option available already in the macros named END_PRINT_POINT_WITHOUT_LIFTING, which still moves the extruder out of the way, but it keeps it at the same Z point. Simply add the “_WITHOUT_LIFTING” to “END_PRINT_POINT” under the “END_PRINT” macro, and you're good to go.


3/14/2024 (Revision 2): In effort to try and minimize friction, I have moved the roller closer to the center of the gantry, lowered the sensor mount and also moved that closer to the gantry. Please leave thoughts, comments, suggestions, and makes!

3/3/2024 (Revision 1): Revised to move the roller toward the middle of the gantry.

Tagi