Prusa XL Logitech C920 Pro HD Mount - EnXLosure Compatible
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A small magnetic corner mount for the Logitech C920 intended to fit on a Prusa XL, and that fits in the EnXLosure.
- Ocena
- 0 / 5
- Polubienia
- 13
- Pobrania
- 87
- Wydruki
- 0
- Wyświetlenia
- 679
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Share Alike
Overview
This is a simple mount for a Logitech C920 (sometimes called a “C920 HD PRO” or other names) to hold it on the upper corner of a Prusa XL. The mount is surprisingly stable with just two magnets, and it fits in the inside corner of the EnXLosure if you have one. (You don't need one, though you are somewhat more likely to accidentally bump the camera if you don't have anything in the way.) A small cable clip is included on the model to manage the webcam cable: in my EnXLosure, I have routed the USB cable along the aluminum and out the back of the printer, just under the EnXLosure in the back.
A picture showing the general field of view of the camera when mounted this way is included: it was taken during a print, so it's a bit blurry and I hadn't tuned the exposure of the camera yet - it takes better pictures in a timelapse. However, in this location, it cannot view all of the bed, so I've included the picture so you know what it can cover.
Requires two magnets to hold it in place, and is currently designed with two 15mm diameter, 3mm thick magnets. (The FreeCAD file is provided, so if you have differently-sized magnets, you can modify it. You will need more than a couple tiny ones, though.)
This print is designed such that both the magnets and the camera can be used as friction fit pieces: neither requires glue, although you can glue the magnets in if you want. I have also added a hole for a US standard tripod screw in the back: a ¼-20" screw (I used a half-inch long one with a washer for good measure) can help secure the camera, but in practice it probably isn't necessary.
Even with the camera extended towards the bed at a 90° angle, the extruder does not quite hit the camera, either when probing the bed or extruding the priming wipe for extruders 4/5. (If you have a print that goes to the extreme near corner of the print bed, it will slightly brush the camera, and may push it side to side a bit. This does not appear to impede printing, and really only affects about the square centimeter closest to the corner. But again, bed leveling and priming wipes for all of the extruders don't touch that area, so only a print deliberately in the extreme corner will brush the camera.)
Note: according to this website, the Logitech C920, C920x, C920s, and C920e are all physically the same camera, with the occasional exception of a privacy cover. I used a base model C920, but the mount is likely to work with the other models as well.
Printing Instructions
- Material: I used PETG, as it will be inside my EnXLosure and may get warm. If you don't expect to use an enclosure, PLA will do fine too.
- Infill: I used 10% for a little extra structural integrity, but in practice the stress isn't large and less would be fine.
- Supports: I printed using PLA supports for the magnet areas. If your materials are good at bridging, supports may not be necessary.
- Orientation: I printed this upright, to avoid harsh angles. Printing on its side may provide a slight amount of additional structural stability, but I have yet to have any indication that the upright print is under undue stress.
License and Included Files
This model is licensed under the CC BY-SA 4.0 license, but please let me know if you intend to sell copies of it. (You're welcome to do so, I'm just curious.) The FreeCAD file for the mount is included, in case you wish to make any modifications.