Liczymy pasujące modele…
This is Crush . It's what happens if you take Rush, replace nearly every M3 nut with a heatset insert, put a linear rail into it, make it take straight talons, and swap the main grip with the grip from the Lynx. Build Guide…
Meet Freerunner. Like the summary says, it's a half-dart, micro-wheel, mag-in-front, battery-in-grip, semiauto manual pusher, 80-175fps pistol-format blaster. I like to think it's pretty good. Pretty quick to print (10.5hr of print time…
“So is this just another PCAR then?” Yeah pretty much. But it's a nice one. Only one part to print, with a snug barrel retention, copious venting for underbarreled applications, and multiple models to support different FPS scales. Is it…
If you've been in the foam blasting hobby for any length of time, you've probably heard of the Fidlock holster system. It's pretty great - put a couple magnets on whatever, and now you can securely hold that whatever onto your body. If…
Introduction If Freerunner was so cool, how come they never made a Freerunner 2?! Well here it is. Now it's more aesthetically pleasing, shorter overall, with an all-new grip, and a shorter trigger pull for faster firing. Still capable of…
Description Introducing Blitz : a solenoid-powered, talon-fed, micro-flywheel pistol capable of any FPS between ~80 and ~170. Compatible wheels: Traceur wheels: https://roboman.net/products/traceur-micro-flywheels-25mm-spacing-1-pair…
Intended for use with nerf blasters to accommodate longer-range blasting, these risers will tip your sight down by 2 degrees which will allow you to zero further out, or use sights that otherwise can't adjust low enough for your use.…
If you're like me, you enjoy the Warp Saya for holding your mags. However, if you're like me you also had a bit of a pain stringing them up due to the shock cord being just a little too big to easily go through all the holes. And if…
Picture a Worker Nightingale. Now give it a bigger battery. Now make it take Talons, Kodas, and Tachis. Now make it hit anywhere from 80 to 180fps. That's Traceur. One screw to get into the blaster. Four to change out the flywheel cage.…
My Boom grip, now remixed for the X-Shot Longshot. New this iteration: knurling. Neat. Uses one M5 bolt (either 30 or 35mm I think) and one M5 nut. Designed to be printed with the front end up - it'll bridge over the picatinny's end, no…
Meet Remnant, the Lynx 2.1 remix. Features from front to back: New Adjustable SCAR muzzle Locks right into the body pin, holds a 40cm barrel in place without the use of the usual barrel thumbscrews, vented, nestles inside the pump without…
SCARs are great. Personally, I find them to be the most accurate and reliable form of muzzle attachment. However, building SCARs is my least favorite thing. Not anymore. The QuickString makes stringing your SCAR a breeze, and attaching it…
This is the LockSleeve BCAR. It's what I use for competitive matches, and I think it's pretty damn good. It has two pieces: the Core, and the Sleeve. The Core has 6 "fingers" that sit around the barrel and are flexible. The Sleeve has…
It's like Midlock, only it's a lot thinner and uses way fewer heatsets and bolts. Now instead of 6 screws holding the front plate to any of the 12 heatsets in the thigh plate, with pulling all 6 required to adjust the angle, there are 36…
Introduction A replacement frontend for the XShot Motorized Piston Pump blaster. This shroud replaces the stock front orange piece (and its collet). It uses the tension-band barrel retention system I've been using on some of my personal…
Heavily inspired by Thanh's RIPPCAR (https://outofdarts.com/products/thanh-rippcar-variable-line-segmented-sla-printed-resin-pcar) Haven't tested it a ton but it's worked real well on my Lynx and Kunlun so far at the 250fps mark. Before…
Uses either 9 or 15 MF63ZZ bearings (https://www.amazon.com/MF63ZZ-Shielded-Flanged-Flange-Bearing/dp/B07K78GY7N) and an equal number of 8-12mm M3 countersunk screws…
TWO VARIATIONS! First variation: M3 heatset and 8mm bar =============================== Hardware requirements: 8mm smooth rod, lengths anywhere between 120mm and 300mm (or longer, I suppose) M3 heatsets…
Introduction Riot! is my answer to “I like Blitz but this event's cap is 200fps”. Utilizing Quickdraw motors and Manshee wheels, this blaster comfortably hits 200fps on 3s and up to 220fps on 4s (though your ears may not love you for that…
I absolutely adore Ehdrien's retro styled VFG, but it felt a little small in my hand. Now, all four of my fingers can fit on the front. Required hardware: 4 x M3 x 10mm screw (two of which should really be button heads so you don't rub…
Want your Alchemist to be that much better ? Look no further! Linear rails offer buttery smooth motion while restricting all forms of wiggle and rotation. As an added bonus, this means that nothing ever touches your barrel, so your…
Uses 3 M3 bolts and 3 M3 nuts per pair. I usually run two pairs per set of mags, just to keep them from wobbling. Works well with straight talons, tachis, and kodas. The magazines are turned 180 degrees from one another that way your…
This replaces the “Stock” and the “Buttplate” from the original Cynthia files.
Designed for the LeedleDynamics Corsair ( https://www.etsy.com/listing/1509623188/corsair-break-action-single-shot ), but will likely fit lots of blasters with Picatinny rails. Intended to hold half-darts, but will likely hold most…
It's Crush, but smaller! Still using a linear rail (but 100mm instead of 150mm now), still super smooth, but now targeting Humans vs Zombies FPS values! The STLs are preoriented for once. Follow the build guide on the Crush page for…
What is Bruiser? Bruiser is a nightingale-mag-fed, solenoid-pusher, microwheel-powered, semi-automatic flywheeler. Pull the trigger a little bit and it revs the flywheels. Pull it the rest of the way and it fires the dart. Bruiser is…
Like the idea of the LockSleeve BCAR, but wish it was a SCAR instead? Well, here you go. Features: 45 steps per rotation ~83mm/3.3inches of strung length Copious venting The same awesome LockSleeve tech as the BCAR for holding it to your…
Not every blaster needs to fire darts at 250FPS 50 times a second. This little guy was created to solve a very simple problem: I want to have a fun little pistol for plinking at zombies with in Humans vs. Zombies. It achieved that goal…
Uses: 9 3mm x 7mm x 3mm F683ZZ bearings ( https://www.amazon.com/dp/B07Z3DRZX9 ) 9 3mm x 14mm steel dowel pins ( https://www.amazon.com/dp/B07Y58JKMC ) This piece replaces your Zinc 2.0's front piece and integrates a 10 degree BCAR into…
Like your Rush, but wish the grip was a bit smaller? Wish no more! By the power of cutting out the old grip and sticking this one in its place, you can have a Lynx grip instead :D Updated 8/28/2024: Uses Crush v1.9 (or higher)…
A BCAR for your Trion. Attaches to the orange plastic muzzle attachment point. The first few times you attach/detach it, it may be very tight on the last little bit, but it should wear in to be a snug-but-doable hand twist. If you can't…
Meet Thomas. So-named for its visual similarity to a certain 1920's lead blaster. I went through a few (8) revisions to get this juuuuuuuust right in my hand. My hand isn't particularly large - a bit bigger than the average woman's hand,…
There are lots of angled foregrips out there, but very few good vertical ones. Here's a good vertical one. Print the bits as shown, then put all the bits together. the pins should be a pretty tight fit. Mine friction fit tightly enough…
Uses the lever and insert from the remixed file. This remix adds a lip around the top-rear side of the hole, preventing over-insertion of the talon mag in the adapter. Tested with a Stryfe, may work on others too. Also uses M3 socket-head…
See "Differences of the remix compared to the original" section. Important: you will need to modify your aluminum bar for this remix. You only need a drill and hand saw to do this. The modified bar is in the .step file, and the change is…
It's like the Fudd foregrip, but smaller! Intended for lower FPS cap games where you'd really want to use a short barrel in your Cynthia. Uses the Dart Guide and Top Rail from the full-size Fudd foregrip. All the same hardware too, with…
A visual rework to most of the external bits of a Zinc 2.0 Muzzle SCAR is remixed from the linked file. Frame is remixed from the original files at https://github.com/118design/ZINC Trigger Guard is my own design Category: Sport & Outdoors
Update 9/8/22: Added looser-fitting cover after reports of overly-snug covers. This is a 3-print, 3-layer (9 bearing) BCAR for foam blasters. There are vents near the base to allow excess pressure to escape without fishtailing the darts.…
Highly recommended that you print this in PETG or another semi-flexible filament, as the clamps have to flex a little to grab and release darts/shells. PLA will work but its longevity may be affected. Replaces the FrontPanel and…
Aaaaaalchemist - all the fun and practical improvements of the Alchemist by Sillybutts, but now with 10mm more of draw, bringing its performance on par with the Talon Claw T4. The entire blaster is only 10mm longer as well. Only two…
Now the hybrid magwell has a Lynx Grip and uses the Crush sear and trigger. You'll need to get the Trigger and Sear files from the Crush (linked as a remix here) You'll need to get these three from the Rush Hybrid-lower listing (also…
Update 8/24/22: Uploaded new version of everything. Bearings are now centered on their flanges instead of their bodies, which better reflects which parts are in contact with the darts and improves accuracy. Vents have been made larger and…
A knurled horizontal pump grip for your Tulip. Replaces the original priming block, mounts to the linear rail and priming bars. All the same hardware as the original.
I like pump grips. This one's pretty large, because the blaster it's going on is also pretty large. Feels good to me though. Textured for easier gripping, flared base to rest the side of your hand against. Uses one M3 x 30-40mm screw No…
Crush, but now with Rush's grip. Update 8/28/2024: Uses Crush v1.9 (or higher) trigger+sear+plunger
SLAB handguard, now with full length picatinny rails on the bottom, left, and right.
Print front-down, with tree supports as shown highlighted in blue: Uses one -016 O-ring (stuffed into the recessed ring like in a Lynx turnaround). Be sure to put a tiny bit of lube on the o-ring - just enough to wet it. Update 12/18/24:…
This skin replaces the Frame, Lid, Battery Door, and Orange tip of the standard Traceur and adds a top rail. It uses the same grip scales and all of the original internals - if you've already got a Traceur, you can drop in the flywheel…
Lightly modified the Rush lower to take the Crush v1.9 (and later) Trigger, Sear, and Plunger Update 9/5/24: Modified the trigger area of the lower to increase contact with the trigger at rest
Uses RedCowl's fantastic barrel collet dev kit for barrel retention: ( Link ) The two big parts print muzzle-down. The lid (green) prints with the rearward-facing angled side on the bed. The little yellow hook prints on its side. Rail…
Important note: print the BCAR bodies muzzle-down! Much like my other BCARs, these all use F683ZZ (3mm x 7mm x 3mm) flanged bearings and 3x14mm dowel pins. These also use the same -016 O-ring as Sillybutts' MXL spigot scars (more info at…
Replacement front piece for the Rival Pilot that turns it into a muzzle-loaded MEGA-only integrated-PCAR beast. 80-90fps or so. Highly recommend pairing it with the thumb-release at https://www.thingiverse.com/thing:5830514 and disabling…
Yet another Lynx 2.1 aesthetic remix. This one only accepts 40cm barrels (no barrel retention screws) and only has a Koda magwell (if you want talon, do it yourself). The shroud has a modeled support wall on what will be the bottom side…
I had trouble finding scope rings that were tall enough to use with my Talon Claw with the IVI Talon Claw 4 Skeggox Stock ( https://www.thingiverse.com/thing:5163077/comments ), so I designed my own. These rings are 1.6inch from the top…
I've gotten a couple requests from folks who see pictures of my mag couplers and think that they're decorative rings for a single mag. Turns out, it's not that hard to adjust the model to be exactly that. Here ya go, a decorative magazine…
This is a conglomeration of the SpeedDrive direct drive mount, the 3DFused linear rail mount, and the Hero Me Gen5 system (has the original Ender 3 mount points). It requires a pancake stepper (the StepperOnline one is what I used), as…
A mashup of Silent Night and the Zinc grip: Zilent Night. Takes Zinc magazines (though it only works with the 10 and 13-round mags because the "chamber" is much higher up on Silent Night than the zinc, so in order to be able to grab the…
Yet another Boom grip, this time for the Game Face Trion. Takes two M5x25mm screws (I used button head, but socket head would probably also work, though it may be less comfortable on your hand). Print as exported - with the flared side…
My Boom Grip, now remixed for the C4. I haven't printed this one since I don't have a C4, but I have the C4 Step files to build it from, so it should be fine. Uses the original hardware from the C4 Doom grip. Category: Sport & Outdoors
All the things I made for the Mini Claw MC4 that aren't the Skeggøx stock (see my profile for that). The Muzzle+BCAR uses a barrel that's cut down to ~132mm or so - it's threaded so it can be used with barrels that are pretty close but…
A replacement for the DOOM grip, but vaguely reminiscent of a shotgun's grip, thus the BOOM grip. No picatinny, just ribs for your hand to grip onto. Keeps your grip closer to the barrel, which theoretically should mean less of a torque-y…
Replaces the first "T5_TCbs" (the one that screws right into the Upper) and gives you the original picatinny rail, as well as one that's offset at 45 degrees. Useful to run a reflex+optic combo and feel just soooo tacti-cool. I ran it for…
Install it with the side with the thicker “wall” on the right side of the blaster
Thingi's remix-linking thing is busted again. This design uses the MuzzleNut_v4 from https://www.thingiverse.com/thing:4929499/files Adds Sillybutts' o-ring-based barrel retention mechanism to your Trion. Replaces the orange muzzle tip…
Same as my Boom Grip for the Talon Claw T4 ( https://www.thingiverse.com/thing:5397595 ), but remixed to fit a Pump Action Skewer. print vertically with the front (the skinnier side) down on the bed, with supports on the bed only. I tried…
Print it flat on the side with the built-in support flat on the bed. there's another built-in support inside the stock. You shouldn't need any slicer supports for this. One M3 voron-spec heatset and one 8mm M3 thumbscrew are needed
I like the Y-tho. I didn't much care for its grip, and I didn't care for the reliability of its feeding. So I grabbed the grip off the Skewer (…
I wanted to make a Kinesis Freestyle 2, but better. Between the Keeb.io Sinc, the FR4 plate kit, and this 3D print, I've accomplished that. The pieces tent the keyboard at 15 degrees. The print just barely fits on my Ender 3 Pro (you've…
Shoutout to the haters. short and long versions
This is a mashup of the controller mounts used with this https://www.thingiverse.com/thing:4257873 Valve Index stock with this https://www.thingiverse.com/thing:2057419 stock. It uses the controller clamp method from the Index stock, and…
Follow the guide for the original QuickString, just.. y'know, twice. You'll also need the insert and tip files from that set. This is just the dual-body.
Uses a printed pegboard hook interface and dummy Mantis holster (no latch or carrying point) to allow for hanging blasters with the Mantis Lug. Fold the hook in half and stick it into the pegboard, then slide the dummy holster down from…
To wszystkie aktualnie dostępne wyniki.
