Liczymy pasujące modele…
Easy to print on its side. Once printed, remove the build-in support plate. It should be fairly easy to pull out with pliers starting from the hole. Does not require any additional support. Print was designed for 0.2mm layer height and…
I liked the idea of the original but because of all the small holes it takes forever to print. This version uses horizontal slots in the sides and also an interlaced bottom, making it print in about half the time of the original. I also…
I wanted to try the Igus Drylin bearings on my Prusa Mini, but I wasn't happy using the original bearing brackets to mount them as it is very easy to over-tighten the bolts, pinching the drylins. The model this remix is based on holds the…
Like Rilot's design, this model attaches to the lip below the trigger but leaves much more space for normal trigger operation. The lock can be flipped using a single finger allowing for one-handed operation and you can easily switch…
I tried about 5 different version of the Y-splitter but the filament kept snagging on the edges of the entry of the tube. Finally decided to create my own version. This version takes into account the wider 2.5mm inner diameter of the…
I didn't want the door to my Platsa enclosure to be all the way open when printing PLA, so I created this simple door stop. It is one piece, print in place. Doesn't require any supports.
My filament sensor was making a lot of noise and adjusting the lever screw did not solve it. When changing filament I started noticing that the filament did not move smoothly through the sensor at all. I opened it up to see if it needed…
Liked the original design, but my PTFE tube was probably shorter than the original arm was designed for so it didn't fit. Instead of just shortening it, I made it so that it is usable for a variety of lengths. The STL contains a…
I didn't want to depend on ‘snapping’ an airtag in a holder so I made this model that needs to be screwed together. No chance of the airtag falling out accidentally. The two different parts can be combined to either make a holder with a…
The center console cubby box of the Mini Countryman U25 (model 2024/2025 depending on your continent) is very handy and easy to access, but as it is quite deep it can get very messy inside. Trying to find anything means digging and…
Loved this cooling duct option but when I printed the original I found that the cooling duct would hit the pins at the back of the print bed (see image showing the damage on the duct). This does not happen very often as you would need a…
After trying many different filament clips, I settled on this one. It is a remix of https://www.thingiverse.com/thing:2817985. I only made it wider and rounded the edges a bit. The advantage of this filament clip is that it doesn't twist…
I didn't like the available sheet holders, mainly because they were all one piece. This version will use a lot less material and is easy to install. Holds 3 sheets. Print with the sheet slits facing upwards. Doesn't require any support.
This model is based on https://www.printables.com/model/58456-prusa-mini-z-axis-support but uses less material, can be printed without any supports and has clearance for use with alternative Y-Axis bearing holders:…
Ornament in the shape of a golfball. All parts can be printed without any supports. Note that the tolerances are based on a 0.2mm layer height. For the snap ring it is advisable to disable elephant foot compensation or add a brim.…
I have a separate spool holder to the side of the printer for when I use abrasive materials or TPU and use a Y-Splitter so I can easily switch between the AMS and the spool holder. I just didn't like a loose hanging PTFE tube. So I…
Camera mount for the Eufy 2K Indoor camera. For mounting the camera in the top, front, right corner of a Ikea Platsa enclosure. This will put the camera in a position that allows you to view the entire enclosure. Easy to print, doesn't…
I was looking for a creative solution for a coat rack and decided to use Ikea Kungsfors kitchen racks. I just was not a fan of the steel hooks that are sold by ikea. So I made my own. There are three hooks A standard one that requires…
Had the same problems as described by Daniel in the model this remix is based on. But as I had threaded inserts laying around I decided to use those instead of the original which uses printed threads. I used 2x M3 threaded inserts by…
To wszystkie aktualnie dostępne wyniki.
