Liczymy pasujące modele…
A simple smaller stand for flyers up to A5 size This is a bit larger and more stable, we have enlarged the compartment for more presentation material, and raised the front for a possible logo or title. Attention, the size of the back…
StealthBurner Main Body for KNOMI 2 Added support for the 5015 fan handle Since StealthBurner is printed without supports so the overhang on the handle to hold the 5015 fan was in the air. It couldn't be printed nicely. I added a…
OV5640 camera the smallest tilting mount with an angle of 0-180° I was looking for a minimalist solution for the camera mount, but everything seemed massive and big, everything is beautiful, but it interferes with the printer's space.…
BigTreeTech SFS V2.0 Voron extended mount by 20 and 23mm lower The encoder puts a lot of resistance to the filament pull, and the extra loop on the bowden cable made the friction worse, and we don't like that. Here is a solution where…
Voron - HEPA + Carbon filter for the ORIGINAL CASE The original part is 55mm deep, the standard Voron filter housing is only 44mm. So we redid it so that we didn't have to print a big box for a big hepa filter, we honestly didn't want to…
VzBoT - Installing BTT PI TFT50 - Raspberry Pi Display LCD Touch Screen We were tired of the constant screen sleep and strange behavior of the FLY LCD GEN display supplied in the assembly kit. We replaced it with a BTT PI TFT50 but the…
Voron Trident - Power inlet - change size to another part The contacts on the switch were bad so we had to replace and adjust the dimensions a bit. We added a frame under the new part to hold it nicely.
Sherpa Micro (ALU version) - ECAS + Switch for MMU We needed to connect to the MMU (ERCF, TradRack, BoxTurtle...) so we drew a component for the ECAS holder and the filament switch. It also works as a standalone filament sensor. For…
VZBOT 235 - Removable Top Hat for original cover Since there is very little space for the bowden and cooling pipes at the top we were looking for a solution for a small overhang of the top cover. A few nice solutions already exist in…
VZBOT 235 AWD - 180° door hinges for CNC kit The original hinges loosened very little and interfered with manipulation around the printer. The remixed model was for the printed version with 2WD, this one is on AWD - CNC kit. In addition,…
WAGO221-413 holder for 2 pcs on profile 2020 We liked this holder, but it was necessary to adjust the dimensions for the 413 version. Print from ABS, ASA, PC or PA (CF)
VzBoT - ToolBox - Magnetic mount The need to store small tools and printing supplies resulted in this low storage box. The assembly is not fixed, it is removable as needed, see photo. The holder is screwed with two M3 SHCS screws (not…
Voron - PSU stabilizer 50mm - 4mm shorter than the original In my set there was a PSU that the handle did not fit, it was all bent and stretched. The modified handle is 4mm shorter, it fits beautifully.
Mini holder power supply converter DC-DC 5A on profile 2020 It was necessary to assign a StepDOWN power converter to profile 2020. Here is a holder with minimal and economical dimensions. Print upside down. Print from ABS, ASA, PC or PA…
VZBOT 235 AWD - CNC kit Diffuser for AirBox - smaller air flow - 66% of the original intake area. When printing large parts with sharp corners from ABS and ASA, the edges of the model came off the PEI (swing - well known). It didn't work…
ERCF v2 No logos and Molex holes, Bottom panel Straight mount For the next project we needed clean and flat surfaces. The cables were routed straight to the ERB board, without any connectors between them. Here are only the parts where the…
Voron - Nozzle Cleaner and Purge Bucket for Kinematic Bed with MGN12 The kinematic bed is taller and the MGN12 brackets prevented it from being used in the original project, so we redid it and added a pedestal on both sides. Possible…
Voron2 300 - Kinematic Bed with MGN12 Since the bed on Voron thermally deforms by 0.5-1mm depending on the temperature. Something had to be done about it, and this solution was quite interesting. We adapted it to the linear MGN12 that was…
CLIP for bag belt - two-piece model You can replace a broken clip with this. Just pull the belt properly and snap it. Print from ABS, ASA, PC or PA (CF) If this helped you, please leave a "Like".
VZBOT 235 AWD - CNC kit AirBox v2 Adapted AirBox corner for frame corner support. When using the triangular aluminum corner 2020 to reinforce the frame, the AirBox will not fit. The modified version has a shortened corner, the flow is the…
VZBOT 235 AWD - CNC kit Z axis extension Extension of the Z axis by 20mm more; final total 220mm. I really disliked the height of the Z axis of only 200mm, the reserve on the rods was sufficient, so 20mm is quite useful. There is no need…
EREC - Magnetic Cover for Cutting Arm Great project, but we were bothered by the fact that to remove the cover we had to dismantle the 2x M2 screw, now the magnets are 6x3mm. Changed M2 heat insert to magnet 6x3mm. Changed hole on M3 heat…
VZBOT 235 AWD - CNC kit ArduCam Mount Camera tilt angle adapted to CNC kit We don't like looking into the fan and extruder, so we needed to see what the nozzle was doing on the table. Two models were produced that have an angle of 10 and…
VZBOT 235 AWD - CNC kit Back Motor Cover L/R side With screwdriver hole for disassembly Print from ABS, ASA, PC or PA (CF)
A Really Simple Energy Chain Holder for Profile 2020 We were looking for a simple energy chain holder and finally came up with this simple component.
Voron2 - BED mount Aid - Kinematic Bed with MGN12 When mounting the MGN12, an aid was needed to properly adjust the bed position. Here is a device that will help with correct alignment with the front, just insert it into the 2020 profile.…
Vacuum cleaner floor nozzle O-ring
ERCF 40T Gear - Nema17 - No logos and Molex holes
EREC for ERCF1 - bearing version 623 and V623 EREC - Magnetic Cover for Cutting Arm here .
To wszystkie aktualnie dostępne wyniki.
