Liczymy pasujące modele…
Overview : I wanted to replace old, poorly printed jumper wire holders with something that would work well with a tray I made from ½” birch plywood that is carved out in the middle for Clickfinity plates by NoWarranty (…
Overview : I designed these bit holders within the Gridfinity system by Zach Freedman. The 2x2 version holds five standard small plastic bit cases, and the 2x4 holds five small and five medium cases. Both versions are stackable. I also…
UPDATE (Dec 7-2024) : I use these components regularly and have not had problems, but user Smitty rightfully pointed out the printing strength for the clamps in the default print orientation is the weakest. I've added two more versions of…
Overview : I have several painter’s poles that adjust to various lengths. I’ve developed a number of attachments for them, but the ACME thread definitions in Fusion 360 are not compatible with the ¾” (075) x 5 tpi definition used for…
I wanted a box to help capture the small vinyl pieces while weeding Cricut projects. I found several out there but decided to build my own with an easy-to-use threaded lid. I've included the Fusion 360 file if anyone wants to modify it.…
Overview : I recently purchased a Sunlu S4 dryer that I also print out of. Unfortunately, I have had issues with the dryer pulling the PTFE tube inside the unit and jamming the spool. I figured I could install PTFE couplers in the…
One of the knobs on our Masterbuilt Sportsman Elite smoker broke, so I modeled a new one. I painted an arrow onto it with a silver Sharpie. I used PLA, and that has worked fine for well over a year. Prints without supports.
We recently remodeled our basement and installed a used Dynamo Arctic Wind Air Hockey Table. The size of the pucks for this table are smaller than standard ones, so I designed one that matched the puck that came with the table. Different…
Overview : One of my hobbies is programming electronics, so I created a tray that I can move around as needed. The tray is made from ½” birch plywood that is carved out in the middle for Clickfinity plates by NoWarranty (…
Overview : Gunk built up along the Y-Rail lead screws would accumulate inside the gantry and would need to be cleaned frequently. I made this wiper to greatly reduce the amount of dust and debris getting in. I can confirm this works with…
Overview : I have recently begun organizing several neglected areas in the house using Zach Freedman’s gridfinity system. This bin provides storage for a container of Amazon Basics dental floss, finger nail clippers, tweezers,…
UPDATE (Sep 21, 2026) : I've created a version with an increased height which would allow other bins to stack on top without bumping into the Arduino board. The original version has a height of 2U in Gridfinity terms, so I’ve added a 3U…
I've struggled to connect several tools to my dust collector or shop vac. I've included several adapters that have worked great for me. Note: some parts should be printed out of TPU: Bosch GCM12SD Miter Saw - This saw has a goofy dust…
Overview : My family works on a lot of electronics projects and regularly need to solder on pin headers to sensors, boards and other modules. To ensure the headers get soldered on square, we insert them into a breadboard and use this…
Overview : My family plays a lot of yard games and cribbage. I have several nice metal sets of cribbage pegs, but it is nice to have some printed ones when I don’t care if they get lost. Others I’ve tried or designed either required…
Overview : I use my Qidi Plus 4 primarily to print engineering filaments that generate toxic fumes. I have a duct fan hanging on a nearby wall, so I ran cheap flex duct from the printer through the fan and up to an exhaust port to my…
I designed this bracket and cover to store my J-Tech 7W Pro laser when I'm not using it. I use the laser with a OneFinity CNC. The bracket requires the laser to be stored upside down, so I also made a cover to keep dust out of it. I've…
Overview : I have a set of small Kobalt metric and imperial wrenches that came in small pouches. Every time I need a wrench, I have to dump the contents and scrounge for the size I need. I finally designed a storage solution for them that…
Overview : I’m a woodturner and have several chucks and even more sets of chuck jaws. They have been rattling around in a drawer for years until I finally decided to create some gridfinity bins for them using Zach Freedman’s system. I…
Overview : My family plays a lot of cribbage, and I’ve designed a lot of boards. I have a hockey stick prototype I made that we travel with. I designed this threaded box to store the pegs with a holder that attaches to the board and holds…
Overview : My in-laws own a cabin that has a number of orioles and hummingbirds but an aging feeder hanging from a tree. We recently installed a new aluminum square railing, so I decided to design a new feeder to attach to it. The design…
Overview : I have two sets of taps that I use for my 3D prints. One is a small imperial set which is a 1x2 bin, and the other is for metric and imperial (a 2x4 bin). They both have a space for a handle and are labeled. The larger one also…
Overview : We have several keys that look identical, so it can be a pain trying to find the key to unlock the house at night. I designed this cover to fit a Schlage-68 style key. To install it, slide one end of the key in, then push the…
Overview : I was recently making some picture frames, and my miter gauge would shift ever so slightly which messed with my mitered corners. I decided to build a rigid, accurate sled. It works great! This sled has holes that can be used to…
Overview : Collet collars usually have a dimple or mark that you can use to tilt the collet in that direction to pop it out. However, some don’t, and some can be stubborn. I designed this simple tool to be printed in TPU to help remove…
Overview : I occasionally make cornhole boards, so I designed some jigs to make the assembly quick, accurate and consistent. I make my boards out of ¾” baltic birch plywood and secure all parts with pocket screws. I designed two sets of…
Overview : I had an old pole where the male threads had snapped off. I cut off the top section of the pole that contained the threads and cap, then modeled replacement ones. The cap slides over the pole’s shaft. The fit should be very…
Overview : My Sovol SV08 came with a tool to help with hotend clogs. It is a thin (1.1 mm) piece of wire with a loop on one end. It actually works quite well, but I wanted to design a handle that makes it more comfortable to use. I…
Overview : I designed this storage bracket to attach to the side of my CNC table. It stores the spindle wrench, collet wrench and the spacer used to focus my 7W laser. I’ve included the Fusion 360 file to modify if your wrenches are a…
Overview : I have a Onefinity CNC (woodworker elite) as well as a Huanyang water cooled, 80mm spindle. Within my workshop, I have 6” spiral pipe for dust collection that narrows to 4” spiral pipe by my CNC. I reduce that to a 2.5” flex…
I have several pair of folding reading glasses that fold in a way that protects both sides of the lenses. This allowed me to design a simple case without worrying about adding foam or other protective measures. Here is a link to the…
Overview : I designed this general use hook to thread onto any standard pole that uses ACME ¾ x 5 tpi threads such as painter’s poles. I regularly find the need to hang or reach something up high. I’ve included my Fusion 360 file and step…
My wife and I recently learned how to make my mom’s designer soap, but we don’t have some of the fancy tools she does. I decided to design my own and started with this chamfer tool or soap beveller. Key features: - The design includes a…
Overview : I ordered the D-ring anchors below that fit into the stake pockets of my flatbed trailer. They work great, but there is too much slop, so they tend to rattle around in the pockets when there isn’t a load secured. I designed…
Overview : I have a very old, but very trustworthy dehumidifier that has been running for many years. Unfortunately, the threads to connect a garden hose snapped off long ago, and I lost the container to collect water. I have been using…
Overview : We recently purchased an Energizer Smart 2K Doorbell for our home. In order to charge the battery, the package comes with a special tool to remove the doorbell from its mount. Realizing this tiny little tool would get lost in…
Overview : Our family and extended family plays a lot of yard games, and a recent favorite has become Kuub. I made my own set and used scraps of ½” rebar as stakes to mark the boundaries. However, these can be a trip hazard and outright…
Overview : I have an AI Dot camera installed by my CNC, and had it mounted above and behind the machine. This was not optimal when doing 4th axis work as the spindle was always in the way. I created this mount, so I could move my camera…
Overview : We have several bubble-style “while in use” covers for our exterior receptacles, but wasps like to make nests in them. This adds quite a surprise when you open a cover to plug something in, and they can also damage the…
Overview : Years ago, I made a “Splat the Rat” game for our church festivals and had come up with a fancy collapsing set of legs and braces to make it more compact for storing. However, it was a pain to fold all of the legs and braces at…
Overview : We received a request to make several of these stands for our high school soccer team. They were seen during world cup games, but we couldn’t find a source to buy them, so my son designed this one. They work great to have along…
Overview : My son loves water sports, so he is typically in charge of our in-laws boat when we go to their cabin. He struggled to fish the boat cover straps under the boat while it was on the hoist in the lake, so I made him this…
Overview : I have a Onefinity CNC (woodwork elite), Masso G3 controller, JTech 7W Pro laser and a JTech 44W laser. I designed backing plates to mount the JTech controllers to the back of the Masso controller. I have two versions: 1. JTech…
Overview : I have a Onefinity CNC (woodwork elite) and recently picked up a JTech 44W laser for it. The laser requires air assist, so I purchased a solenoid valve that could be controlled by the CNC controller (Masso G3). This simple…
Overview : My wife and I occasionally make soap and needed a place to dry the bars after cutting. I found an old grate from an oven, but it wasn’t flat due to the lower section that kept it from falling out of the oven. I designed these…
Overview : I recently installed air assist for a new laser on my CNC and wanted custom brackets to secure the wire loom running from the solenoid valve to the power supply and controller. I designed two versions: - Standard Bracket: This…
Overview : The top bracket of our church’s Broadman communion wine dispensing cup broke, so I modeled this one to replace it. I also modeled and included a replacement cap if needed. It has been working well for the past couple of years.…
Overview : Our large, extended family spends time at a family cabin and uses Solo/Hefty cups for drinking glasses. We have always used a Sharpie to put our names on them, but that has at least two issues: - Permanent marker (Sharpie)…
To wszystkie aktualnie dostępne wyniki.
