Liczymy pasujące modele…
I remixed https://www.prusaprinters.org/prints/24951-prusa-mini-filament-sensor-holder-v2 because I didn't have an m3 square nut available and the thread of the printed m3 square nut was to weak. Hence I adapted the holder for use with a…
This mount fits into the one of the two card slots on the front of the T-Loc-Systainer generation and holds one hearing protector (e.g. 3M Peltor Optime 1) and two pens or two googles. It does not! fit into the newest generation Systainer…
This is a remixed version of https://www.thingiverse.com/thing:2816006 . It allows you to mount a Festool rail or any other rail with the same width and height on the left or right side of at least two T-Loc Systainers (not Systainer gen…
Remixed version of the Sheet Holder by RoboMagus (https://www.prusaprinters.org/prints/35073-prusa-steel-sheet-holder-open-front) adapted to the size of the prusa mini sheets (80,78% X and Z axis, 80% Y Axis) with tighter sheet slots and…
This is a remixed version of https://www.prusaprinters.org/prints/42178-nozzle-holder-cap for the Prusa Mini. The Nozzle Holder fits on top of the y Axis using the screw holes. Print with 6 Top Layers, 15% Infill, 0,2mm layer height,…
I bought one AC Infinity T3 ventilator and sawed out two openings in the back up of my Besta tv lowboard. First installed just an opening as in the photo, later added a second compatible usb 120x120 fan and added the model with the round…
This stencil/ruler features ticks every 2 nautical miles (nm) and 2 minute ticks at 80, 95, 110kts groundspeed measured from the square cornered edge marked by the arrow. At the opposite edge the tool provides a space to measure a 5+5nm…
Model 1 is an ¼ inch to Quadlock base adapter. You can combine Model 1 with any of the original quadlock mounts (e.g. magsafe or charging heads) or print a basic one yourself (Model 2). No supports needed. Printed with 0.10mm Layer…
A remix for the excellent model created by @benoitmeunier_93241. For me the phone was to front heavy with the microphone added to the adapter and the wind fur showed up on camera, so I turned the cold shoe part around by 180° and moved it…
Inspired by a pilot workshop episode about total electric failure and the use of a backup handheld nav/com, I adapted a holder for a different handheld to my Yaesu FTA-850l, so I can mount it on the dash and not only use it for backup…
Original version: https://www.thingiverse.com/thing:5232416 Adapted to fit Q3 RTK HYX Composite Ringkolbenzähler from the company Pipersberg used by the water provider MAINOVA in Germany. Be aware that the ring holding the lid ist…
This is my take on a car visor mount for a Käuferle garage opener. Its a tight fit with low tolerances. The mount expects a visor with a thickness of about 19-19.5mm, this is the case with the Skoda Octavia 3 and I guess most cars from…
I removed the rear hole
This is a remix of the Hyperpixel 4.0 Pi 4 Case by superwoodle. My remix contains a mounting adapter wich can be screwed into a enclosure wall e.g. LACK with up to 3 countersunk screws with a diameter of max. 3,5mm. The case has been…
For the ipad get a case without a fixed folio. I just ordered this one with a detachable folio. Add official MAG ring. Use thin double sided tape to secure the ring to the print and the print to the iPad case. The adapter perfectly…
This is a component (part 31 or 25 on the explosion chart) of the fence holder for the original MFT 800 /1080. All the other components are available to order as of 07/2021. You can gain a few centimetres of cross cut capacity by using…
Allows opening the case while on the mount. Offers a place for the dji mic series mobile receiver and the soft case.
Snaps into the small recess behind the lens and can stay on the AcePro. On the other side it press-fits the FSTOP-LABS filters. The press-fit is not as secure as the original magnetic mount, so I wouldn't rely on it for action sports.…
This is remix of https://www.thingiverse.com/thing:4246377 and https://www.thingiverse.com/thing:4570340/remixes . With the remix bearing holder by 3opaH you don't need to buy any nuts as the bearing holder is threaded. Because they were…
Used to mount in the cockpit of a Piper Archer 28
This project includes everything needed to build a bed occupancy sensor inspired by https://community.home-assistant.io/t/fsr-the-best-bed-occupancy-sensor/365795 : One PCB design for connecting two FSR sensors to an Lolin ESP32-C3 pico…
Quadlock adapter/mount for the “Decathlon BTWIN Ultralight 1 Second” How to Print: Pause Print at 6.2mm, add the m5 hex nut and resume. Support for the overhang required. Installation: Remove the rubber stem cover to get to the hex screw.…
Use it with any of the original quadlock mounts (e.g. magsafe or charging heads) or print a basic one yourself. Supports needed. Printed with 0.10mm Layer Height, GoPro prongs pointing up. Pause at 9mm to add a M5 hex nut. 1/4 inch to…
For this product: https://www.eisenschmidt.aero/zubehoer/pilotenzubehoer/koffer-taschen-zubehoer/85/flight-bag-size-s-dfs-pilot-line
Support on build plate needed. printing is possible on either side.
To wszystkie aktualnie dostępne wyniki.
