Liczymy pasujące modele…
Holds 12x AA batteries. Prints upside down (load batteries from top) without supports. Note: this will NOT fit Duracell AA batteries. If you want to use Duracell (or similar), you'll have to scale the X and Y down to 97%, but not the Z.…
This drawer fits underneath a Nespresso Inissia machine, specifically the one made by DeLonghi (once upon a time sold at Costco). It may also fit under the other Nespresso Inissia (such as the ones made by Breville or Krups) machines, but…
Prints upside down (load batteries from top) without supports. So far confirmed to fit the following batteries without modification: Amazon Basics Eneloop Duracell ProCell
This is my self-designed, 3D printed, handwired, mechanical keyboard. It's a 75% layout with clickable volume knob and runs on QMK Firmware, so you can reprogram it to whatever you like. This is an extremely involved project and is too…
Assuming you're using the same (Geekworm X630) HDMI-CSI bridge (…
The original holder for the inductive probe / sensor on my Sovol SV06 was cracked, so I designed this to hold it instead. Why this design? The original Sovol design isn't easy to print, and it requires heat-set inserts. Other designs I…
This is a small tray that mounts to the SV06 rail behind the screen. It gives you space for printer spaghetti waste or for tool storage. I printed mine in PETG, 0.3mm layer height. Upright with snug supports. STEP file included for easy…
I was able to print this on a Sovol SV06 with 15% infill, default walls, and .20mm layer height, PETG. Supports are most likely required. I used PrusaSlicer's organic supports. EDIT: Make sure you use loctite, lock washers, or locking…
I wanted to add a coat rack to the side of my Ikea Kallax bookshelf, so I designed this! It fits on either the left or right side of a Kallax, and mounts without any modification to the Kallax. Prints without supports if you print with…
Remixed ThantiK's bed catcher to install on the two front corners of the build plate as well!
Prints flat with no supports! I printed mine in PETG, with 0.15mm layer height, 50% concentric infill, and 6 perimeters for strength. It's held up my pants and supports the tools on my belt just fine so far! STEP file included :)
Print one of each file. They just snap together without glue. Please note: depending on the tolerances of your printer, this may be a very, very tight fit onto the motor shaft. I had to scrape mine out a bit with an X-Acto knife before it…
I was looking for a way to unobtrusively add more light to my room. A lamp would work, but takes up footprint in real estate I don't have. Behold - putting a light bulb behind my monitor, screwed into the VESA 100 screw holes! Why not…
This spacer drops into your Hydro Flask Cooler Cup to allow your 12oz. can to be used with the 16oz. cooler! Prints in any filament without supports. Layer height, perimeter, and infill don't matter, but you can save material and print…
Prints flat with no supports! I printed mine in PETG, 50% concentric infill, and 6 perimeters for strength. For the first 2.39mm, I recommend 0.15mm layer height for strength. The rest should be 0.10mm layer height or thinner, for…
Remix allows Eightbit's clipper hanger to be used with AllTheHobbies' tool rack on the SV06.
I want to hang clothes on my closet doors. But there's not enough clearance over the top of the door to use a typical over the door hook you could buy at the store, so I made this. It's super thin and super light. Uses barely any…
A small carrier to protect your Woody's arrow lube from breaking if you drop it. But also prevents you from dropping it because it has a built in mounting point! Remove the label from the lube container before you attempt to put it in the…
Lets you put an architect lamp into the top of the VIVO monitor arm pole. The dimensions may not be correct if you have a different kind of lamp than mine, but that's what the STEP file is for :) Print in a durable filament with ~5 or…
To wszystkie aktualnie dostępne wyniki.
