Liczymy pasujące modele…
This is a mockup model of the QTR-8RC and QTR-8A line sensors from Pololu. I made it to help me designing my new line follower and hope can be useful for someone else. Dimensions used were found on the Internet because I don't have the…
I created a maze solver bot (aka micromouse) for the contest at 2017 OSHWDem held at La Coruña. To test the bot, a maze with actual dimmensions is mandatory so I've created this parts. Micromouse_Maze_Wall.stl -> Generic wall of 170mm…
I've remixed the great "Slew bearing with crossed cylinder rollers" by Isi3d to be able to specify different parameters for the inner and outer rings. Separated variables for inner and outer rings, allowing you to customize the number,…
This is a WIP to create an enclosure for @Tysonpower's DIY Hörmann RS485 Bridge v1.2 (HCP Emulator) PCB. Model was designed for tight fit , your printer must be correctly calibrated or parts might not fit. Enclosure characteristics:…
Remixed from http://www.thingiverse.com/thing:878919 I've printed the Angled Dry Box Feeder by sarman_1998 wich came out very good but wanted to change the size of the fixation screws. When I started to mod sarman_1998's STLs I found they…
I was in need to replace my weared off 3D-printed idler pulleys, the ones i got for replacement have Ø5mm bearings and are a bit wide for Toolson's idler so I've remixed it. First of all, I've widened the pulley receptacle to accomodate…
I'm building a maze solver (micromouse) based on Escornabot ( http://escornabot.com/web/ ) open source educational bot. This bracket was designed to hold an Arduino UNO on top, since Escornabot uses a different board. EDIT 09/28/2017:…
I've downloaded & printed the great and simple "P3Steel - E3d V6 bowden dual extruder mount" by outcastrc. The problem I found is that the air wash, that flows though cold-end, go downwards after getting trapped between the X-carriage and…
I've printed http://www.thingiverse.com/thing:703700 some time ago to mount my FPV monitor to the Taranis. Thing printed very well, and fitted both the taranis and the monitor, but the screen angle was too flat for me. To solve this, I've…
This is a remix of my 3D printable Micromouse labyrinth Walls & Connectors. I've removed most of the walls and replaced it with a 2,5mm hollow plastic sheet. It uses same connectors. You'll have to print 2 of Micromouse_Maze_Wall_End.stl…
This is a SIMON 24 mechanism holder Plate I made for my father in law as he was not able to source new SIMON 24 mechanism plates anymore. Original ones are made of galvanized sheet metal that gets corroded with time. Model consists of two…
I'm using the sidepots of my Taranis to control pan and tilt of my Zenmuse Z15 in a 1 man set up. Always felt they were awful to handle. To solve this I've decided to make a longer-front facing lever. They fit like a hat over stock…
This is a holder fot th status Led of the Wookong (the non-BT one) It also work as a tulip for the LED making easier the reading of the LED from far away, from the sides or below. The part consists in two pieces. the holder itself and a…
This is basically a modification of the DeltaPanel by scottmayson to mount the Smart Controller ( http://reprap.org/wiki/RepRapDiscount_Smart_Controller ) board to the front of the P3Steel chassis. The knob included here is exactly the…
The LED of DJI S800 ESCs is soldered in the bottom of the PCB and protrudes. This makes very easy to damage the LED if you not take care when leaving the arm in the ground. Also, l wanted to label the arms to know instantly which motor…
This is a remix of http://www.thingiverse.com/thing:155659 to accommodate the DJI Wookong GPS on top of a Carbon Core (Pre Cortex Models) top plate. It has a flat base to stick better and guide holes aligned with the ones on the plate to…
To wszystkie aktualnie dostępne wyniki.
