Liczymy pasujące modele…
This is a remix to address some issues I had with the original design. Printing info: PLA 0.4mm nozzle 0.20mm layer height 15% infill [UPDATE 6/22/2026] Per request, here are the diameters for the steps on the original model as posted.…
I made this because I lost the pin to one of these fasteners on my motorcycle. I decided to make the entire fastener in case I needed the whole thing. 0.20 layer height 100% infill Brim used on pin print by object instead of by layer…
I made these hooks to mount on the garage wall to hold my fishing poles. I didn't like using nails due to the scratches they made on the fishing rods. I used PETG since my garage gets warm in the summer. They are mounted with a standard…
I made some fork guards for my NC750X. I have included 3 model files. One has ‘Honda’ text, one with ‘NC750X’ text, and one that is blank. I secure them with a zip tie in the slots on the tabs. They should fit other motorcycles with…
Supports required I used .24mm layer height I used PLA+ 10% infill, adaptive cubic
This is a wide nozzle attachment for a Ryobi model#RY40402 40V leaf blower. I made it to speed-up blowing leaves and grass clippings off the driveway. It replaces the original (round) nozzle that is included with the blower. I used two…
This holder provides better access to the Bowden tube on the back of the machine than when using the factory spool holder on the back. I added a filament guide post to provide a more consistent path for the filament between the spool and…
Remix of Bowling Pin Keychain by DCA_prints.
This is a clone of the chip bag clips my wife purchased for potato chip bags. She wanted a shorter version for smaller bags so I made this. Why a two-piece model you ask? I wanted to copy the original version as close as I could because…
I made these end clips to hold the halves together while starting to wrap the yarn.
This is a replacement cover for a triple head electric razor. I made this as a replacement for my Norelco Series 3000 razor. I am not sure what other models it may fit. I used PLA but other materials should work as well. 0.4mm nozzle…
I made this ‘dead pedal” cover for our CX-5 since the floor mats do not cover the dead pedal. The carpet in the CX-5 is known to wear quickly if you put your foot on the dead pedal. This should fit 2017+ models. I cannot verify if it fits…
I made this oil filter change funnel for my riding lawn mower to prevent making a mess when removing the oil filter. The location and orientation of the oil filter make it difficult to change without oil dripping everywhere. My riding…
I made this ‘dead pedal” cover for my 2023 Nissan Frontier truck. This should fit GEN 3 models 2022+. I cannot verify if it fits any other Frontier model years. Some 0.75 inch wide velcro is needed for the back side to secure it to the…
I recommend using TPU for this with a hardness of 98A or higher (TPU for AMS). Print in the orientation as supplied in the .3MF file for strength 0.20mm layer height 2 walls 15% infill Arachne walls supports required
DISCLAIMER! THE AUTHOR OF THIS MODEL ACCEPTS NO RESPONSIBILITY FOR PERSONAL INJURY OR DAMAGE FROM THE PRINTING AND USE OF THIS DEVICE! PRINT AND USE AT YOUR OWN RISK! This clamp holds the engine STOP lever on TroyBilt push mowers that…
My wife asked if I could print a checkbook cover. I searched for models online and they were all too bulky for her. She just wanted a simple cover like the banks used to give you. Based on information I had read about using different…
I decided to make this wallet after printing several designs I have found online. Many were very nice but were lacking in one or two areas. The key features of this design are: Holds up to 7 cards (I have 8 in mine because 2 of my cards…
To wszystkie aktualnie dostępne wyniki.
