Liczymy pasujące modele…
These blocks have been designed to be used with the Ender 3 V3 SE and KE models only. Another user has verified that it will work with the KE model. The right and left side are slightly different heights as the plastic molding thickness…
Wydruk około 1,10 €–1,34 € nettoWstępna wycena jednego wariantu
This model comes in two versions. One with eyes and one with eye cutouts. You can use the printable eyes to make them a different color or use flatback beads or other items. This print requires no support or brim. The model can be printed…
Wydruk około 1,56 €–1,91 € nettoWstępna wycena jednego wariantu
This articulated jumping spider comes in two versions. The first is a single model with eyes. The second version has eye holes and you can either print the eyes separate in a different color or use flat-back beads. You will notice that…
These guide rings will help correct the crooked x axis belt and reduce fraying of the belt. Prolonging the life of the belt. You will need to print 4 rings total. 2 for each pulley that is on each side of the x gantry. The left one is…
This model is a fully mechanical version of the golden egg from The Goblet of Fire Harry Potter movie. You can also add a tea light or a fairy light to the inside egg. This model assembled (with base stand) will be 19 cm tall (7.4 inches)…
This model has been altered to have a large thick key-ring loop so that it can be made into a key-chain. The original also has a butt loop but it is much smaller and thinner. Suggested scale for printing is 65%-80%. I was able to print…
This is a pokestop spinner from the Pokemon Go game. Unlike the other models out there (at present) this one spins more like the real pokestop, with the center circles spinning together. This spins very easily and has plenty of clearance.…
This is a remix of the demiguise statue by NBAU https://www.thingiverse.com/thing:6192949 I have divided the model into 3 parts so that the sphere can be printed in a different color. I also have made this model so that a tealight fits in…
Articulated grateful dead dancing bear. There are two versions. One has a keychain loop on the head, the other does not. This model does not require supports nor a brim. As for scaling: I suggest looking at your slicer output to determine…
If you like cryptids, then check out my other monster model, the Flatwoods Monster https://www.printables.com/model/1013664-flatwoods-monster-figure-cryptid This model prints in a few parts. No glue or extra hardware needed for assembly.…
It prints fine at 0.2. All of the ones in the photo were printed at 0.2. Some were painted. !! The tongue requires a little brim but otherwise no supports or brim needed for the body. I have uploaded a file of the head with a little brim…
This washing machine container has a base of 100x100mm when printed at 100%. You may want to size up a little bit to hold a full bag of laundry pods, depending on how many pods you buy. I made this with really strong hinges and that is…
There are two versions of this case available, a cutout version with heat vents (as pictured) or a solid one. The solid one can easily be customized to have your own cutout design. You can use windows 3d maker and Tinkercad together to do…
** If you like cryptids, be sure to check out my Mothman model! https://www.printables.com/model/1036948-articulated-mothman-cryptid --- The model is designed to be stationary and does not articulate. This model requires some glue for…
This model prints in two parts and will need support for the main block part on the convex face side (the chin and nose). The base has two cylinder shapes to guide alignment. You should glue the two pieces together. See photos for which…
This is a figure model of Twink from Rainbow Brite and can be used to make any of the Sprites or your own color choices. This model comes in multiple pieces that use pegs and glue to fit together. You will absolutely need to use glue for…
This model prints in two parts. The head connects with a snap connector. This connector is not a circle but an oval. You need to make sure the face aligns with the front of the body, tilt the head to one side, insert the prong lip on one…
Did the plastic housing on your USB flash drive break or is it just ugly and you want something pretty? Well look no further. This ergonomic design will hold standard sized flash sticks. Featuring a reinforced loop, you will be sporting…
Print all parts with a brim. I suggest printing inside pieces near each other so that brims attach together and help keep it from being knocked over. Print at 0.2mm. You will need two of the grommets. Or maybe more. See video to determine…
This is a stinky cheese man figure based from the book The Stinky Cheese Man and Other Fairly Stupid Tales written by Jon Scieszka and illustrated by Lane Smith. A favorite from my childhood. Haven't you also always wanted your very own…
These risers were created for my bed frame which is a Zinus Abel Queen frame. These likely fit other sizes and other brands of similar style bed frames but I cannot confirm that. I have included the dimensions of the 3 models and the…
This case is a remix from https://www.printables.com/model/415036-birthcontrol-travel-holder This case is designed to hold contraceptive birth control blister packs that are 4 rows. The inside of the model contains two restrictive points…
The brick prints at 4cm long and the bottle at 4cm tall. You can make them a bit larger if you want but I would not suggest printing smaller. These are pretty light and comfortable to wear. You probably would want to print them scaled up…
All models in photographs were printed at 0.2mm layer height. Many were painted. Save yourself some time and print these at 0.2! I use Angelus leather paint on my models because that paint is also designed for vinyl. It works great on PLA…
This frog prints in two parts (body and cape). To attach the cape, simply (gently) pull the cape apart and snap onto the neck. Although this is a remix, I have significantly changed the model's face. I have also added a loop on the back…
This is a replacement handle for cheap mini rubber rollers. The roller wheel on these is about 34.5mm long and a diameter of 22mm. These come with a M4 screw that is about 46mm long that you will need for the replacement handle. REQUIRED:…
This is a support bracket to be used with metal frame bed frames. I have two of these bed frames and I have designed two brackets that fit each of them. I cannot guarantee they will fit yours so please measure. I have included images with…
To wszystkie aktualnie dostępne wyniki.
