Liczymy pasujące modele…
Clips around oval pool railings. Print in petg and strengthen the high stress area with more infill. See this done in the 3mf file for my prusa mk3 Bestway 15125 16ft x 48in Power Steel Round Frame Above Ground Pool Set Print Settings…
Yet another pushrod keeper. However this one has two new features: It works with thicker 3mm thick 3d printed horns It has a notch so you could use needle nose pliers to snap the rod into place. THREE pushrod sizes are offered. 0.8, 1.0,…
Another servo horn but my Prusa can print the splines. 24 tooth spline. Make sure you size it so it fits tight. Category: R/C Vehicles
Customizable nose cone for ELF DLG. Need to print in vase mode! Comes out about 1gm heavier than the original. If you like it, you can send a tip via PayPal to [email protected] Print Settings Printer Brand: Prusa Printer: i3 MK3…
Rescue air boat for my float plane using pvc pipe, 4 soda bottles(Vezu soda 76mm dia). Note that full throttle reverse may cause the boat to capsize. Program throttle on Tx accordingly. Needs 1/2-inch PVC schedule 40 pipe 45-Degree S x S…
This is a two part FasTrak metro transponder holder that fits onto the circular shaft of my Toyota Matrix rear view mirror. I think this should be similar to Toyota Corolla's as well. Note that the fit around the rear view mirror shaft is…
This is a super light spinner for an Aeronaut yoke 38mm. The 3mf file has specific settings merged from 3dlabprint.com that enables super light weight thin shell printing. Weighs less than 0.1oz I didn't have a fine enough scale to find…
print at high z-resolution. petg recommended due heating inside car during summer time Be sure to insert female part into hatch cover FIRST, then only insert the pin to lock it. You may not be able to remove it once installed....but, hey,…
These are 4 different servo plug cover pairs. Each pair is unique so that it makes it difficult to connect to the wrong servo extension wire. You don’t need to print them in different colors but that would help as well. The design is such…
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/8WopESLnZ9d Use bamboo skewers as axles. I use one M3 screw with washer and one M5 screw. Category: 3D Printing
Customizable bare die tray with lid. Great for making custom MEMS chip holders or chip carriers. Corner tab is there so that specific dies could be labeled with pen or sticker on the cover and the orientation would be preserved. Click on…
I needed a replacement plastic hub/yoke for my Hobby King Folding Propeller hub/yoke. SKU: OR025-02403A By printing this design and any variations thereof, the user assumes full responsibility of injury or death. This is a plastic mount…
I needed clamps to hold a tall fuselage part during printing. It was wobbling too much. These clamps have magnets to attach them to the bed. To keep them from sliding, I painted some Gorilla silicone glue (thin layer) on the bottom. M3…
This is a gate latch for an iron surface which does not require any screws to mount. Using 2 strong hard disk or hard drive magnets, the latch mounts magnetically adhere to the gate surface. At the same time the iron rod (ikea curtain…
I made some custom wing servo covers for the 3dLabPrint Hawker Hurricane. These are most useful for the version of the plane for belly landings. Hopefully they will protect the aileron and servo horns. They are made in LWPLA but in a…
Home Depot squeegee https://www.homedepot.com/p/Unger-10-in-Shower-Squeegee-989800/316417410 needed a holder to hang it in the shower. Category: Bathroom
Believe it or not I've had my Tx fall off the strap. This should add a new level of safety. To unhook from tx, just rotate part so that shackle pin can be slid up: Category: R/C Vehicles
To wszystkie aktualnie dostępne wyniki.
