Liczymy pasujące modele…
In making the Nevermore Mini I wanted to use the full nevermore controller over bluetooth The Nevermore Mini project on Github and Printables has a screen holder for the Pi Pico 1.28" so I remixed it to support the generic GC9A01 screen…
I tried many other alignment guides but found they always had a certain amount of play in them I created this design which consists of an inner piece which is a snug fit for rail and extrusion but has some flex in it. Then there are 2…
Simple Daylight on a stick holder. Hides wires from view and routes them into slot underside extrusion BOM: 2x Voron spec M3 heat inserts (M3x5wx4l) tool to depin your JST-XT 2pin for feeding wires in 2 x M3x8 for mounting daylight 4 x…
If you want to use a Pico and full nevermore-controller with sensors and screen, and you don't want to use WAGOs and you like over engineering things, then here's a wiring solution for you! Remix for Nevermore Mini , and inspired by this…
This model contains 3 mods to A4T you can pick and choose from 1. Sidecar PUG Mount for A4T+WWBMG I wanted to use PUG with my A4T on a Trident but I wanted something rigid and with minimum use of z-height about the toolhead. I created a…
I have a wooden enclosure for my Ender so I wanted to wall mount the Nevermore Mini without tape or magnets Suggest printing with PETG or better Holes can be used with M3 bolts or self tapping screws or similar This mount contains two…
I like the original model but I didn't have screws long enough to use it
I wanted a reliable Emergency stop button for my Voron Not wanting to get too creative on something so important I bought a reliable button https://www.aliexpress.com/item/1005004176517786.html 16mm diameter The print contains 2 parts,…
I didn't like how the mains wiring for the bed was bending around a tight corner so I designed a bracket which attached to the Z1 bracket and through the cable chain mounting holes The bed wiring goes through more gradual bending as it…
I was having trouble with the thread on the original model so I redid it in Fusion 360
I wanted to organise the wiring into my dual UHPs and Omron SSR. I wanted to use wagos and I also wanted a protective cover once it was wired in to keep it extra safe BOM: 2 x Voron spec heat inserts (M3x5wx4L) 2 x M3 screws (sorry will…
Adapted the excellent bracket for CAN cable routing by @ChriL_91518 to use PUG Requires 2 Voron spec heat inserts 2 M3x8/M3x10 countersunk bolts PUG of your choice
I wanted to mount 2 UHP Power supplies and I didn't have tools to tap new holes in my Bakelite electronics bay base I used these as both a drill template and a mount. Drill 4 holes for one end (2 per power supply) and use the power…
I'm using these 2040 brackets on my Voron in any corner I can, but it does make the wiring a fair bit harder https://www.aliexpress.com/item/32893717438.html So I devised a bracket to cover wires: going up from below, around the corner in…
Secure a neoblade to your skadis with this model Use Skadis T-nuts to secure:
I was adding some skirt push buttons to my Voron and found I had a wiring challenge. I wired all the button to a gpio ground pin (common to all buttons) and another wire to the button's individual gpio pin. But then I could no longer…
I wanted to be able to wire my bed heater, thermal fuse and thermistor for easy bed removal. I'm in the UK, so on 240V a second level of insulation or seperation is no bad idea, so I combined my design with a remix of a cover, modifieid…
To wszystkie aktualnie dostępne wyniki.
