Liczymy pasujące modele…
This is a printable 3d scan of the passenger side interior door handle pull. It is a bolt in replacement for the OEM handle which is very prone to failure. The one pictured was printed in PLA, but I highly recommend ABS, PETG, or ASA for…
for those of us who enjoy building our own engines, this tool is meant to help aid in setting the correct clearance between the side seal and the corner seal. Things you'll still need: 1) drill press with locking table 2) drill press…
Here are models to replace your broken seat belt retainers. You'll still need the metal push nuts and spring from your broken retainers. If you do not have the push nuts you can get these: https://www.mcmaster.com/94813A200/
3D scan of the front of an FD RX7 gauge pod. I used it to make a custom gauge holder for a digital dash.
I made this model from a 3d scan of a stock one. It does not have the mounting tabs like the stock one, but its very easy to secure the boot to the mount. This mount allows you to to use and aftermarket boot without needing to buy the OEM…
This is an adapter used to adapt the upper intake manifold on the 20B and 13B engines to a GM 90mm throttle body. I've test fit this on the 20B and REW intakes, but should also fit S4 and S5 intake manifolds.
With the age of these cars the original plastic is becoming very brittle. In many cases as you remove and install parts to service your car the threads in the plastic will break rendering a costly trim piece all but worthless. These parts…
blank panel for the FD RX7 cruise control buttons.
bottle for the harbor freight powder coat gun. Both the bottle and cap are interchangeable with the HF parts so you can mix and match as you like.
This bracket allows you to mount a RX8 DBW pedal into the FD3s RX7 chassis without modification to the chassis or pedal. Should be pretty easy to print, and I would suggest doing it in ABS or PETG only and use a heavy infill. You'll want…
replacement mounting brackets for the drivers side armrest/map pocket plastic. I have included several variations. There are stock ones for direct replacement if your foam is in good shape. there are also reinforced brackets that have…
This is a replacement cover for the manual headlight adjuster knob. The “stock” cover is a copy of the OEM part and would work very will printed form TPU or other semi-flexible material. The “024 oring” model uses a 024 oring to secure…
these are replacement covers for the front speakers. These are known to break and are NLA from Mazda. The covers ARE different between the drivers and passengers side. also remember to print these in a high temp plastic like ABS, PETG, or…
Cover plate for the water pump. Should fit all 13B and 20B engine blocks including the RX8.
This is the retaining clip for the rear drip moldings and replaces Mazda part number B092-50-525 which is NLA. I've tried printing this a few different ways, but FDM printing, even at a fine layer height just doesn't seem to get the…
First and foremost, under no circumstances do I suggest you 3D print this part from plastic and use on your engine! I've provided this model as a mock-up tool only. Use at your own discretion. On that note, I've also included a .DXF file…
Mazda 323 BF 4WD dash surround. I have not tested this print, so if it needs tweaks let me know.
Plate to cover up the hole when your CAS is not installed to keep debris out of the oil pan. Should fit all 13B and 20B engines that use the CAS (crank angle sensor).
This is the bar in the steering column that cancels the turn signals after turning the steering wheel. These are prone to failure and are NLA from mazda. There are 2 versions. the first being a straight replacement. The second is for the…
replacement vents for the smaller defroster vents on the dashboard.
block off plates for the exhaust ports for a BP and BPT 1.8L Mazda engines. I've split the model into two pieces that even smaller printers should be able to handle.
print solid from semi-flexible material.
mounting bracket for the turbo control solenoid when using a block off plate.
this part is to repair the mounting clips on the stock solenoids which are prone to snap off. the intent is to glue these to the solenoids for retention. These mounts do make the solenoids a bit wider so you can't use two of these next to…
replacement large defrost grills that mount in the dash board.
replacement trim for the interior door lock knob. As this part will be subjected to lots of sun exposure I highly recommend resin printing, but if you need to print on an FDM use a high temp plastic such as ABS, PETG, or ASA.
Block off plates for the water pump inlet and outlet for BP 1.8L Mazda engines. May work on 1.6L engines as well, but I have not test fit them on one.
decretive clip that covers the mounting screws on the front cowl.
Lets be real guys, that car on jack stands isn't going anywhere for a while, so why not make sure to keep debris out of your head while the intake is off. Sure you could shove paper towels in there and forget about them after you put the…
harness clips used to secure the rear harness into the chassis. Likely used in other late 80's and early 90's Mazda's as well. These print without supports, but I suggest printing them solid from ABS. The clips are intentionally hard to…
replacements for Mazda part numbers BF6751587 and BF6751597. These should be printed from something semi-flexible as the mounting tabs are a bit thin. I'd suggest SLS printing from Nylon. Design updated 3/20/2026 for better fitment!
Most of these pieces are NLA or have a long lead time from Mazda. all the bushings are quite straightforward. Print solid from a heat resistant plastic like ABS or PETG. Bushing 2 there are 2 variants, one with threads and one without.…
Replacement button for the BF Mazda 323 cruse control "set" button. The tabs that hold it in are prone to breaking, and cool 80's orange likes to fad in the sun. I printed this from orange ABS plastic. No special precautions needed to…
This is a bracket to mount a radio in the lower center console. It angles the radio up towards the driver to help with visibility. It's designed to mount to the "cheaper" double din 7" radios. The one I have mounted is a Rimoody 7". Id…
A remix of Noclue1987's tool, this is designed specifically for use on 40 degree vbelt pulleys. It uses the laser laser and you can use any battery holder, but I've linked the one used below. I just joined the wires together and have the…
To wszystkie aktualnie dostępne wyniki.
