Liczymy pasujące modele…
A basic vinyl stand that can and should be extended with d=6.4 mm lens-shaped rubber feet. The model is oriented to be printed lying on it's side (as in picture 4). For me, it adhered well without a brim on a PEI sheet. I would not…
Note the pointed tip of this sleek towel hanger design, that does not care for the presence of a hanging loop! Save yourself the time of looking for the side of the towel with the hanging loop and just hang it up. Orientation doesn't…
Avoid liftoff from the dirt, on wet grass or in the snow with this highly practical, foldable print-in-place quad launch stand! Nipples are 28 mm apart, so it fits only smaller quads (examples show a GepRC Phantom and a Cinelog25). This…
I printed a left LCD mount from Thingiverse that had multiple makes and comments saying "perfect fit". It was a perfect waste of filament and time. So I replicated the original right side mount from scratch. I also added a ribbon cable…
This is a custom Ender 3V2 mainboard cover designed for the use with a 92x14mm fan (e.g. Noctua NF-A9x14 PWM) in conjunction with a 22x7mm step down converter (e.g. MP1584EN). There are clearance holes for using the fan either in a push…
When my dad gets his Maglite from behind the cabinet, he usually tips it over. So I designed a sideways Maglite Holder for him and a straight one for myself. It is designed for a D battery Maglite (39.4 mm in diameter) and holds my LED…
This model does not require supports when you print the f(r)ont facing the build plate (see third photo). The model already contains supports for the tips of the S and the G. Use a crafting knife to remove them. If you don't trust…
Had my loose cables always stuffed into the side handles of my 4x12 cab until I was looking for a new procrastination reason, which I soon found in the idea of a Marshall Cabinet Side Handle Instrument Cable Holder, or short MC Shich. You…
This is a special mount for TBS Crossfire Immortal T V2 FOXEER Lollipop 3 AXII antennas for the GEPRC CineLog 25 frame. VTX antenna brand/type doesn't matter; it works for any antenna with a connector up to the size of MMCX90. Two…
I needed a case for the Raspberry Pi 5 with Active Cooler that was as slim and simple as possible — meaning no excessive supports. The design does not require any supports and only has minimal bridging at the SD card slot. This is an…
This is the case for one of my Snapcast clients. It houses a Raspberry Pi Zero W and a HiFiBerry MiniAmp . The Raspberry Pi Zero 2 W has the same footprint and will also fit. I only need the PWR IN micro USB, but I have added versions of…
I designed this overhead holder for my toothbrush to prevent chalky water from running down the handpiece causing a mess, and to keep the toothbrush from constantly resting on the sink. I used a 25 mm piece of mounting tape (19 mm width)…
Random 15° GEPRC Phantom Insta360 Go mount, that additionally acts as a front damping support for the battery. I've updated the initial version with a version that uses less material (=less weight) and fits the camera tighter. I haven't…
This naked GoPro case for two cameras and accessories accommodates Two Naked Cameras (BetaFPV V2) Two Micro SD Cards Micro SD to SD Adapter Lens Cleaning Cloth LiPo Adapter Requires: Eight 6x3mm Magnets Two Component Adhesive Notes: Yeah,…
Handle-Equipped Device for Guided Ease HEDGE your pain away—alleviate pain points and ease muscular tension with this fascia trigger tool. Print with 3 perimeters and 3 top/bottom layers. Models can be printed together in the provided…
Since BetaFPV recycles their V1 camera mount as a bottom plate for the V2, I decided to build a better bottom plate. I didn't like that the quadrotor can't be placed horizontally at level and that the USB port is just not accessible, no…
This is a very specific one: A mount for the RushFPV Tank Ultimate Mini with the default antenna for the BetaFPV Beta95X V2. Notes The two cross beams tie the thing together but also fixate the microphone if you use one. The little flap…
To wszystkie aktualnie dostępne wyniki.
