Liczymy pasujące modele…
This keeps baby chicks from spilling their feed all over the place and uses a mason jar. I chose to print in PETG for longevity but be aware the big overhang section is 64 degrees so you will need to either use low layer height or…
I chose to print this in PETG . support required for the tray. designed to take up full bed space on ender 3 (230X230) you could scale down to fit on mk3.
This hand reel is quite handy! I keep one in the truck and ATV for those just in case times you come across and awesome fishing spot. you can store several lures / weights or other small fishing supplies in the handle. I suggest making a…
This nozzle is handy for using old PET bottles as oil squirt bottles in the garage or to fill with water for wet sanding print the applicator in PETG I chose prusament lipstick red at .2 layer height 4 perimeters 20% infill. I strongly…
This is designed to be printed in TPU I find 95A shore hardness works best. .2 layer height, .45 line width, 3 wall lines, and 25% infill are my settings.
I suggest to print in a softer TPU like ninja flex or chinchilla. play around with the slicer settings to get your desired outcome in firmness.
This print in place truck is designed to be easy to print. Tolerances for the wheels are fairly loose and should be easy to print on any printer. I have been able to scale it down to 70% and still have the wheels move freely right off the…
This part replaces honda part number 77207-HA0-000 and fits I most if not all honda atvs. I chose to print this in ninja flex tpu and after some trial and error on slice settings I feel that makes this an upgrade over the factory piece as…
replace your honda 400ex or other model seat catch rubber. I print these at .3 layer height, 4 wall lines, .6 line width, 20% infill. replaces p/n 17611-HA5-000 this part should fit all below honda atv models 1983-1987 ATC200X 1981-1984…
after some experience this is best printed in a 95A shore hardness tpu but you could probably get away with petg just fine. pla works unless you whack something too hard and then it may break. the pictures you see are sainsmart tpu…
water dish for baby chicks, takes a standard mouth mason jar. printable on prusa mini
This is a remix. I have added some hinges to the box to accept 1.75mm filament, filleted the corners and made some smaller changes. also created a lid to go with it. UPDATE: version 2.0-2.1 has a magnetic latch which accepts four 5x2…
these handles fit standard 3 inch bolt/screw spacing. The holes are sized for M4 or similar bolts to thread into the plastic. This has been holding up fine for me. you could resize the holes easily in tinkercad for different hardware or…
door clip model goes into the doors, door clip panel model goes into the door panels. I printed these in PETG and seems to work really well. I would not suggest PLA
I prefer to print these in a softer TPU like ninjaflex. they are made in small sections to be easier to print however you can scale up Z if you like to make them custom sized the A size seem to fit most atvs have been tested to fit Yamaha…
These are designed to be printed in TPU and will be a massive upgrade to your manual tire changer. These parts protect the wheels you are working on and will help to keep your wheels from getting scratched. Print 2 of the wheel guard, 4…
I chose to print this in PETG with .6 line width on a .4 nozzle. 4 wall lines 5 top and bottom layers and 45% cubic infill. this seems to hold heavy coats so far.
replaces the rings on most flagpoles that break. Print at .6 line width, 4 wall lines, 50% infill
this ant guard is designed to work for any humming bird feeder and accepts hooks with 3mm diameter by 11mm long threads. I suggest printing in PETG or ASA for longevity since it will be used outside and most likely see UV exposure. no…
This is a wearable mega man buster if you have huge hands you may need to scale it up a bit. Ive printed this on an Ender 3 and it pretty much maxes out available Z height I suggest having very well tuned supports to print this. this…
restoring that old 400ex and need some new gas tank straps? you are in luck as long as you have a 3d printer and some TPU. designed to be printed in a softer tpu like ninjaflex but would probably work with any. I print these at .3 layer…
These prusa mini foot pads are a bit taller than the oem ones. Glue them on if not using the prusa mini stand mod. If you have the stand they just pop right in. best printed in a softer TPU like ninjaflex.
I designed these feet for the Fokoos Odin 5 f3 to give the printer a more stable stance by increasing the footprint and also allow it to fit on my smaller shelf rack. these also raise the height of the printer by roughly 15mm. designed to…
This is a replacement tool kit strap for Yamaha Warrior 350 all years print in soft TPU 85A shore hardness or softer. I chose ninjaflex
back scratcher styled after a zen garden rake. bring some zen to your life when you scratch that itch! can also be used as a zen garden rake if you have an appropriately sized zen garden. I chose to print this in PETG at 4 wall lines .45…
This replaces the factory bar cover. Relocates the ignition barrel and adds spots for up to 4 switches. Designed to work with the factory rubber mounting bushings so remove those and the metal collars from the stock bar cover and install…
I designed this shower caddy to fit most bath fitter showers with that utterly useless acrylic bar, it just slides over the bar and is held tight in place. Each shower is slightly different so this may be a tight fit or just slightly…
this bracket allows you to bolt up the no dig fence gates that are currently popular at lowes and homedepot to wood posts or siding. I print these on a .4 nozzle at .8 line width .25 layer height, 4 wall lines and 20% infill I used PETG…
I chose to print these in ASA with .6 nozzle 5 wall lines 5 top and bottom layers and 40% infill for strength in my application
Print in your translucent filament of choice. I would not use the higher power settings on the flashlight if you are printing in PLA as the flashlight does get hot enough to deform standard PLA at those settings. the pictured prints were…
This part is a replacement for Honda part number 15804-HN1-000 this fits all years trx400ex Strongly suggest to print in ninjaflex or similar 85A shore hardness material. for best results print at .6 line width, .28 layer height, 2 wall…
yah yah another spool holder but since I made it of course I think its better than everyone elses. this spool holder is wide, hefty and solid but still fits mini spools. has good retention and just looks cool. print 2 of the holder part,…
This was made by remixing the stock fan cover file provided by fokoos. some of the files have the BL touch port removed to make them print well with no support. V2 file is designed to be removable without unplugging the ribbon cable. if…
I designed this bolt tray to go on the back of your Fokoos odin printer and store the gantry bolts when you have it folded down for storage or transport. There are two different mounting options the more solid one is #2 which bolts to the…
Print in TPU i chose a 95A due to small size of the parts
To wszystkie aktualnie dostępne wyniki.
