Liczymy pasujące modele…
A 3 part case for the 2.4 inch ESP32 CYD board with a built in kickstand that folds in flat. I use this with CYD-klipper on my Lemontron 3D printer. Requires 10mm M3 screw to secure the back on and add friction to the arm. Print in the…
A simple little plug to seal up a 3M mask port using the bayonet connector. Made this because I only have one filter for my mask and without something to close up the second hole, it wouldn't be effective. This is best printed with…
Simple modification for the back to make the device slightly lighter and cover up the gap left over the antennas. Because it is plastic, it improves wifi performance. This removes the magsafe magnets as well. The CM5 gets HOT, so you…
Print all parts in provided orientation. Button assembly can be glued in place, but only use a tiny dab of superglue on the bracket between the buttons themselves so they can still move once cured. Any countersunk M3 screw can be used to…
If you aren't already using the new lemonstruder , you should try using that instead of this! This is a modded extruder for the Lemontron that adds torque and helps keep the filament pushing gear from overheating and softening the…
Replaces printer toolhead with a mount for a pen to use your printer as a plotter. Print parts in the provided orientations. This is intended to be printed with 0.2mm layer lines, though you can go finer. Parts should be printed in the…
A compact, all in one PC with a Pi 4 and 4in monochrome CRT. PETG is advisable for the body piece, as the pi 4 can run hot. You will need: All printed parts (print in the provided orientation - window should be a single layer of…
T8 lead screw coupler. what more could you want? requires M3 screws and nuts.
Mount for generic 800S ebike displays on a 35mm diameter cylinder with zip ties Requires 2x M4 8mm screws and 2x zip ties. You may also want to put some rubbery tape between the bike and the mount if it slips around too much. Best printed…
RECENT UPDATE: Modified tensioner screw cap and added shortened Lemonstruder pieces for durability and more range of adjustment I had a lot of trouble getting a K1C gear that could grip filament well enough for my rev E lemontron. I…
A keyboard case for the surface duo. Requirements: Keyboard - https://www.adafruit.com/product/3601 (shop around, there's other places that sell this) 5x 6mm M1.6 screws M1.6 threaded inserts 4x 30mm M2 hex cap screws A Microsoft Surface…
A very lightweight, no frills mounting system for the Ender 3 (I use a V2). Uses 40mm fans, you can even use the stock fans if you'd like. Includes a BLtouch/CRtouch mount, a 40mm blower fan mount for part cooling and a 40mm heatbreak…
Alternative buttons for the Hackberry Pi CM5 You need 2x of the button brackets and 4x buttons To install, get the button brackets in place (the circular nubs facing towards the buttons on the PCB) on the front plate and fix the front…
This mount CANNOT be used during normal printing - you must put it on before use and remove it once finished. Remove the screws attaching the toolhead to the X carriage and screw the mount in place, so that it screws the toolhead back in…
Requires M6 nut to be placed inside, use glue to keep in place if necessary. Use a high infill percentage (I used 70%) to make sure the weight is well supported. PLA WILL slowly creep under the constant load of the weight of the machine -…
Uses 1 20mm M3 countersunk screw and 2 M5 bearings from the original Lemontron BOM to make a spool holder that spins freely, slightly reducing the amount of work the extruder has to do and reducing wear on the spool holder. During…
Adds a handy USB-C port for the Lemontron so you can add a camera or sensor for input shaping, or even external storage if you want. All parts are printed in the given orientation, but you can of course rotate to fit. A 0.4mm nozzle with…
An IKEA SKADIS compatible board for the NZXT S340 PC case. 3 parts to print, unless you can do the full model on a really big printer.
To wszystkie aktualnie dostępne wyniki.
