Liczymy pasujące modele…
Traditional design of B4 mount cap for cameras. Has decorative spoke to find which side should face upwards. Use ironing. Tune you supports well and remove them properly. Their remains shouldnt get in your camera :) DONATE ETH/Polygon:…
This is a remake of very clever design of https://www.thingiverse.com/thing:6474490 I had to remodel it from scratch to allow it to fit real V-mount accessories, since original design is too tall. You still need the backplate from the…
This is a replacement for amaran's adjustement dial. Original cracked for no reason and with no warning. Was designed for 100 series (specifically 100d). Seems to fit 300 series as well. Amaran 100c 100d 100x 300c 300d 300x DONATE…
THIS THING IS PROVIDED "AS IS"! USE IT AT YOUR OWN RISK!!! I'm not responsible if your dear camera hits the ground! This is a two-piece adapter. Main body can easily withstand stretching load. It takes bending but may degrade if you bend…
So, stock TS-Optics (GSO) monorail focuser has plastic body with those stupid curves and 0 extra holes. I didn't want to remake the whole part, so i came up with this. Print this part, add two M4 threaded inserts and sandwich it on top of…
This is my solution to motorize R.A. axis on stock telescope EQ mount. No irrevisible modifications of the mount needed. Just print and snap it on. Accurate enough for visual, nothing more, nothing less. It includes: NEMA17 90 degree…
If you deforked your ETX90, you would probably want to add some accessories on it. Why not use an already existing mounting points then? This adapter fits on original fork mounting points and is held by original screws. It's symmetrical,…
THIS MODEL IS PROVIDED "AS IS"! USE IT AT YOUR OWN RISK!!! I'm not responsible if your dear camera hits the ground! It is really awkward to handle the camera, especially rangefinder without the right handle, so i made one that slots on…
I was building this case model as my project was going and i didn't want to reprint everything every time. So i separated it into baseplate that holds the board, walls and top case. This way you can reprint walls adding new I/O as much as…
Holds Arc, two bit kits, ratchet driver and an empty case in one place. Warning, fit is pretty snug , so consider printing a test crossection and adjust XY comp before going for full print. Requires supports for the case clip. F3D…
Probably there are better ways to do this (teflon film for example), but this mod is still better than stock. Main benefit is that if you have a 3d printer you already have all the parts. Completely degrease the focuser shaft and focuser…
Print vertically with extra thicc walls. It's expected to loosly fit on the original foot, but be tightened by vixen mount screws. PETG strongly recommended because print is expected to be springy.
This is a remix of https://www.thingiverse.com/thing:699347 by MyDogJustice. I changed the holes so this base could fit a wider range of scopes and wider range of screws, so I could attach Celestron 9x50 RACI finderscope to my Meade.…
This type of mount allows you to attach your focuser motor directly to a tube. Designed for ~170mm tubes. This type of connection is extremely easy to print out of PETG and it's nearly indestructible. Clamping is done via M4 bolt, nut and…
This is a remix of @RockNLol design with @LineArcLine t-clip system. Thanks both of you for great designs! Intended for low-profile t-clips. There is a remix for full-sized ones.
Why buy a motorized focuser accessory for astronomical amount of money when you can get high-quality wireless focus motor from the videomaking tech? This was designed for Meade Poalris 127 (~155mm tube diameter) and 15mm rods.…
I bought myself the amazing FlipMirror but forgot to get any gear to attach eyepieces to the top port. While pairing something as classy with Hadley part is far from optimal, it works and is certainly better than nothing, while i'll…
This is a a huge SHC (Smart Hand Controller) case that you can build with just a 3D printer and soldering iron, no custom boards needed. Two versions: Internal LiPo + usb-c charger or external NP-F. I've included a hump to house Dupont…
A cute accessory for your plushie friends. Assemble on M4 bolts. Hinges are fragile and tricky to print. If it does not work for you, you can weld or glue parts together. It may even sit without hinges (worked for one of my alpacas)
This simple adapter allows you to plug stock finderscope of Skywatcher 150p into the polar finder slot of its EQ3-2 mount. While it's far from optimal and not extremely accurate, it's good enough. You can get pretty good aligment by…
The connection that you usually use to rotate the eyepiece in a comfortable poition has play in it, that can mess up alignment. This simple thing snaps on and adds a groove, so you can rotate the eyepiece without messing everything up.…
This clip is designed to clip an assembled vacuum cleaner. It's tension is enough to hold the tool, but you can pull it out with one hand. Fusion F3D file supplied if you want to tune stiffness. v10: slightly increased mount plate…
Some VCT-U14 have this plastic part. Some not. Mine had it and it was cracked, so i drew a replacement. Honestly have no idea what it even does, but all dimensions were copied from the original. Sadly i have no idea of the origin of my…
Sony CA-D50 mentions a mounting bracket p/n 3-690-850-01 to attach a battery adapter or whatever. I doubt that i'll ever see this part in my life, but here is an adaptor which you can print to mount a generic v-mount plate to it.…
You want to attach an additional guidescope to your scope without drilling new holes? All slots are occupied? Clamps to the rescue! You can't have too many clamps on your telescope. This is very fast and easy to print clamp that can be…
Warning: photo equipment repair common sense required! Disassemble stuff at your own risk! There are springs and miniscule screws that hate humanity are very easy to lose. You need photos or photographic memory to put it back, so take…
Uses low-profile t-clip geometry. Uses M4 bolt and nut to tighten the cap of the iron inside the holder.
You print this and embed three M4 nuts into it using soldering iron. Now you can tighten the mounting screws on your focuser full force like no tomorrow without bending the tube. This will remove play when mounting heavy eyepieces or DSLR…
This attaches as graflok extension and accepts a standart focusing screen. Makes the whole setup easier to carry and swap while reusing original ground glass. Use two M2x16 with captive heads for things that focusing screen grabs on.…
Traced from original plate that i happen to own. Test-fitted.
Well, this thing allows you to attach relatively cheap Smallrig 2987 directly to HEJNE. It has enough thickness to allow pressing on the release button. You put two M6 hex-head bolts in it, then attach the adapter to 2987 via either…
My used Meade Polaris 127 came with several retaining fins broken off the endcap. No wonder, i guess it falls down all the time (with a lot of noise). I didn't want to waste a ton of plastic to print a whole new endcap, so i designed this…
This simple plate allows you to attach that weird mounting foot of ES 10x60 to existing M4 holes on your GSO RC8. Insert four M4 nuts into the base Chose four M4 screws for them that won't go too far in and damage your scope body. At…
Some repair operations on sony Betacam SP VCR PVV-3 require this fixture. Never saw a rel one, so i created this based on illustrations from service manual. It is not perfect but it does the job. It is not as rigid as this part should…
This is a simple addon for BD-04 clips to fit it over aputure 100d stock reflector. It will not dangle. V4 file: added slits for tighter fit. New version will not come off the BD-04. Print slowly and with some supports. will probably work…
I don't know about you, but unlocking tilt axis on tribex was traumatic for me multiple times. This simple handle friction fits on the stock handle to give you better leverage and, most importantly, prevent your fingers from colliding…
IO plate is a removable component, mine is designed for X7SPE-HF-D525 flavor (two NICs). Fits both MiniITX and slightly-extended not-actually-FlexATX flavors. Top lid is optional and can mount an SSD. Height-wise is fits PicoPSU, but it's…
To wszystkie aktualnie dostępne wyniki.
