Liczymy pasujące modele…
Go ahead and divide 39 mm by your desired size and use that number as the size modifier to get a buckle of your desired size. Make sure to print with the flat side down and the tab facing up.
This is a remodel of another case found here on thingi. I modified it to show off the camera module more and change some clearances to fit better after printed on my ender 3. There's also a version (v.3) that is connected between the top…
I had plenty of strength and stiffness in petg printed with 6 perimeters of .5 mm extrusion. This prints in 2 pieces flat. Heat up the forks and bend them into the position seen in my photos. It helps to run it under cool water to cool…
This is my attempt at a dimensionally accurate model of the S21. I used it as a tool to make a case. I have included the .stp in "case" you would like to do the same. The .stp and .stl files should be pretty freaking close to the actual…
print with no infill, all perimeters. should be ok in pla and definitely works in PETG
Made to print with no top or bottom layers on a .4 nozzle Print with three perimeters and .16 layers. If you print with these settings then you won't need infill. Print Settings Rafts: No Supports: No Resolution: .16 Infill: none…
Not printed and tested yet but the dimensions should all be good. I am planning on using a small velcro strap or maybe a short voile strap to keep the tube and compressed air cartridge in there. Category: Sport & Outdoors
Print with 5 perimeters, 5 bottom and top layers, and no infill. Printing with no infill lets the shells have the flex necessary to bend open as you put it on the bar. Make sure to print with the tube oriented vertically, as shown in the…
Print with the widest layer width you can for optimal strength. This was printed with a .6 nozzle and .8 mm layer width. print in vase mode! The shape of the wall is more than just looks. The shape of the walls adds to the rigidity of the…
ATTENTION: this requires mirroring on the x axis. This is like the 20th version of this case for me. I am really happy with the fit. It should not require any scaling or adjustment. At least it doesn't on my ender 3 v2. The back of the…
Easy to fit together. Probably best to print in PETg as some flex is needed but not too much. This is a remix of The Same Name Twice's "Rugged Parametric Box" that has seen so many other remixes. This should be able to hold most common…
Adapts ford transit roof to flat surface for placement of standard 14 inch RV vent. Print in 4 separate pieces. Difficult to print without warping. Probably best to print in some material that wont deform in hot weather like PLA would. If…
Printed these out to hold my skis on a wall. Still need to find something grippy enough for the camming surfaces to hold my skis.
This is a kickstand for Surface book. I have a 13 in model but I bet it works for the 15 in too. Category: Electronics
This lets you move the stock fan from over the z and e stepper drivers to above the x and y drivers (these are the ones overheating on e3v2). I also suggest doing 3 other things. Remove the board from under the heated bed to avoid that…
This is a pen for use in Juani_cer's thing #4808398. A super cool spherical joint that uses the flex of the plastic to allow movement of an axis along a spherical plane. This should be the perfect length to have the tip right at the focal…
Each file needs to be mirrored and printed. Then glue the two halves of each piece together. First, glue the ball together and sand to remove the larger ridges then put the ball inside the two halves of the main thing and glue those…
Topo map of the grand Targhee ski resort. Effective resolution is 10 DME. Could be useful on foggy days on the mountain to navigate by touch hahaha. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No…
This is a protector card for the vaccine card. In Utah it is about 3 in by 4 in. I have heard other states have different-sized cards. Category: Other
To wszystkie aktualnie dostępne wyniki.
