Liczymy pasujące modele…
A simple two line brake clamp for automotive 3/16 line. Overall OD should be around 0.19in for a snug fit. Uses a single 4mm allen cap screw and nut to secure two brake lines. In theory you could scale for other line sizes but I have not…
Improved Pool Venturi Jet printed in PETG designed to inject air into the pool and raise the PH even if using a solar cover. Uses nearly ideal venturi angles and ratios. Very effective air injection. This is an improvement over my…
A pool nozzle that includes an air siphon for injecting air into the pool Jetstream. It uses an overall 0.75in port and is designed for Hayward style 1.62in diameter pool Jet. Injecting air into the pool can increase PH without additional…
A simple thee line brake clamp for automotive 3/16 line. Overall OD should be around 0.19in for a snug fit. Uses a two 4mm allen cap screw and nut to secure two brake lines. In theory you could scale for other line sizes but I have not…
Print on flat end, without supports.
Mandrel for making coils out of 3/16 brake hard line. Can be “unscrewed” from the bent line after forming. Produces coils with 0.25 spacing out of 0.19 OD brake hard line. Make up to 5 coils with a OD of 2.2 in. Can use pliers to catch…
Simple 2 gauge pod for a 1965/1966 Ford Galaxie or LTD. Uses the existing trim screws but need to be swapped for slightly longer #8-1" screws. Hangs 2x 52 mm (or 2") gauges and 2x 12mm (or ½") switch holes. Prints in two parts, the bezel…
3/8 bolt power block or terminal post with a 2" spacing that has the same footprint as a Ford starter solenoid. Useful if you are removing the fender mounted starter solenoid on a classic Ford. Uses a 3/8 bolt at least 1" long. Print it…
Horn Retainer Ring for 1965 and 1966 Ford Galaxie/LTD/others. I added fillets to a couple of sharp edges, but otherwise modeled directly off of the original Ford part. Not sure about the long term durability but fixed my problem for now.…
! Updated to v3 - I forgot I had not mirrored the top. Updated the top to print directly from the stl now. Bottom had a couple of typos in the small punch sizes A case I made to store/organize a set of old gasket punches. I think they…
Holley 4150/4160 or Autolite 4100 Intake Block Off Plate. Very basic block off plate for most non-spreadbore intake manifolds. Used to prevent junk from falling into your intake when storing or when the carb is off. Very basic part, just…
Loosely based on the PI card deck case by dktosoch on thingiverse (https://www.thingiverse.com/thing:2844013) this is a completely scratch modeled design that incorporates space for an OBDII connector at the rear and a seed studio CAN-FD…
AC Door Actuator for 1965-1968 Ford Galaxie to use a more modern Jeep blend door vacuum motor. The original is no longer manufactured. This is to replace the vacuum actuator on the top of the factory AC Box which frequently dies as it is…
Small box for storing loose LEDs. Nine compartments with 1.5x0.75 cubbies. Snap on lid. Quick and dirty and prints in about an hour on a Prusa MK4 on fast. Could be useful for small hardware, bulbs, capacitors, batteries, pins, etc…
1.25in EMT Conduit Clothes Rack End Cap Use this cap to provide a hanger stop when using a piece of 1-1/4 in EMT conduit as a clothes rack. Snaps over the end of the cap and prevents hangers from sliding off the end. No fasteners needed,…
To wszystkie aktualnie dostępne wyniki.
