Liczymy pasujące modele…
My wife thought the "Curvy Pen Pencil Holder" by SpaceDog3D would make a good orchid pot, but it needed drainage in the bottom. This is the result. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution:…
This is a relatively quick design of a servo based nozzle brush for an ender-5 style cube frame. You will need an F695-2RS bearing and an Hitech HS-225MG servo, and a basic wood handle brass brush as found in many hardware stores, and…
My elderly dog tends to push his food bowl around and eventually ends up flipping it over onto the floor. This is an attempt to produce a bowl which he won't dump out. As well, by providing a large surface around the edge for him to place…
I needed a mounting bracket for a Tekonsha Primus IQ brake controller. The Primus IQ is an older style than the more common Tekonsha Prodigy brake controller series, and uses a slightly different mounting tab setup. Since there were no…
This is a simplified version of the low poly plant pot drip tray, without the clip connectors. This was remixed specifically for this orchid pot , though my printed version of it had been scaled down in size. Print Settings Printer Brand:…
This plug/cap fills the original heater ducting off from the fan shroud of an air cooled VW Type 1 Beetle engine. The plug end is tapered slightly to make it easier to press into the duct for solid engagement with the edges of the hole.…
This is a replacement cap for the common aftermarket oil filler tube on an air-cooled VW engine. The threading is M46x2.0mm. Depending on which filler neck you have, you may need to scale the X and Y axis. This should fit on the 45 degree…
This covered water bowl is intended for goslings or similar water foul who need to be able to stick their head into the water to drink, while preventing them from turning it into a poultry wading pool. Category: Pets
This is a universal hanging mounting bracket for the Planet Audio P350MB, and very likely fits additional 1-DIN head units that share the same retaining ring clip mounts on the sides. I designed this to be able to mount a 12v car radio…
NOTE: This is for the AMZ version 1, the new Mega Zero v2 seems to need the mounting point resized a bit before this will fit. The FreeCAD project is included if someone else would care to remix things to fit that version, or I may try to…
This is a center cap for a Formuling steering wheel with a 78mm hole and approximately 5mm plate thickness. It features a 1970 VW logo, which can be printed in a second color if desired. TPU is recommended, otherwise you may not be able…
This is a shim to put behind the EMPI Baja Headlight Housing when mounted on fiberglass fenders. It brings the headlight forward aproximately 30mm to improve clearance for large tires, as well as angling the headlight downward 8 degrees…
This bracket is designed to hold a Meanwell RS-15-5 power supply, as well as this HiLetGo "D1 mini" relay shield with the +5v ground and signal wires soldered directly to the board. The intent of this item is as a standby power supply for…
This is a quick replacement connector for a broken solar light kit that came from harbor freight. Print this laying on it's side, using supports, for maximum break strength in the required direction. Category: Outdoor & Garden
This is a modded version of the "Badnoob" AB-BN 28 (also AB-BN 30) Dragon hotend rear half, with a simple BLTouch probe mount added off the left hand side. The vertical offset is non-exact so you still need to space things out with some…
This is a simplistic adapter which can be used to mount a v2 Starlink Dishy onto a 1.90" diameter Flagpole Buddy Aluminum pole. This is an effective replacement for the official version, in case yours has been lost or possibly just left…
The control panel was pried off the front of my Winchester safe in a break-in. Since the panel was originally screwed onto the front before the stick-on button pad was attached, there was no way to directly replace the screws. Instead,…
To wszystkie aktualnie dostępne wyniki.
