Liczymy pasujące modele…
I made these for my Kenmore 158.1913 and 158.1941. They fit on the push/pull clutch and make it easy to turn the handwheel. The two parts clamp on the handwheel using two screws, but the grip comes from several small pieces of removable…
These parts clamp to the original handwheel and makes the Singer 99 easier to control by reducing speed and increasing punching power. I printed the parts using PLA+ I coated the handwheel with wax and bedded it in epoxy for a perfect fit.
The Kenmore 158.1703 sewing machine has a left homing needle. These plates allow the user to have a Center-Homing or Right-Homing Needle instead of the factory default Left-homing. To use, select the CAM position and set the stitch width…
This is a temporary plug for the gearbox in a Kenmore free arm sewing machine. I made it for a 158.1941. It may fit other models. I made it slightly oversize so you may need to sand it to a perfect snug fit.
These are small computer speakers that are a modification of an existing “boombox” design. I used the design by Tom Zarbo found here https://www.youtube.com/watch?v=zCrpgpnYlOo and made them into separate speakers. I used the same box…
This mod for the handwheel gets the speed down, torque up, easier to control speed with pedal, easier to turn handwheel, still fits in cabinet, still sews faster than I can, sews all the denim I can cram under the presser foot. This is a…
The Kenmore 158.1703 has a small handwheel that some find painful to use. This bolts in place of the original and uses the original screw to hold it in place. I've made it a tight fit, so be prepared to scrape and sand it to get a perfect…
This part adds a reduction pulley to the Kenmore 158.161. I suspect it will work on similar models like the 158.540. The mount uses a pulley from a Kenmore 158.12511. This pulley may also be found on models 158.12510, 158.12512, 158.12520…
This model was inspired by Whitewings gliders. With its straight lines, this design is easy to trace and cut, and economical to make using file folders. Use a heavy cardstock or a file folder. Align the template with the grain of the…
The Magicyoyo N6 is inexpensive, smooth, and small. But the flat hub face makes it difficult for me to fingerspin. This insert is simply pressed in place. Sand it smooth before you press it in. It also makes the yoyo heavier at 70 grams.…
With my center-homing 158.1756 Kenmore there was no way to select a right position for the needle. Use this and set your machine to the CAM setting and the ZZ width to the maximum. I used PLA+ Four layers and 50 percent infill.
It's hard in the U.S. to find a Singer 201 without a potted motor. This allows a reproduction hand crank to be fitted. The magnets are ¼" cubes. Put a single layer of masking tape between the adapter and the wheel with the adhesive side…
This plate allows the user to position the needle for straight stitching. Use the CAM setting, insert plate, and then use the width dial to put the needle where you want it. I tweaked a previous model and the print is a little ugly, but…
Convert from treadle to a motor using these parts that are held on with magnets. The bigwheel keeps the speeds appropriate for this old machine and makes low-speed control easy. It uses 24 ¼" cube magnets to hold it in place. The machine…
This device pushes the lower follower to the extreme right position. To use, put the dial on the CAM setting, push the follower release lever to the right, and insert the device with the upper follower in the hole. The needle will now be…
These ugly old Kenmores are cheap and unloved, but built like a tank. This Bigwheel clamps on the original handwheel and makes sewing thick fabrics much easier. You must remove the bobbin winder assembly and cut off a small part of the…
To wszystkie aktualnie dostępne wyniki.
