Liczymy pasujące modele…
This little knob converts an M3 bolt into a finger-adjustable bolt, eschewing the need for a finicky Allen wrench but still keeping the head available for secure tightening. Simply thread an M3 bolt of your choosing into the hole, with a…
This box securely holds 25 prepared slides, with plenty of space for each slide to avoid breaking them.
These little eyepiece covers sit on top of your eyepieces, preventing dust from falling on them while idle. Print flat, so that warping is limited, and they should print with no problem.
This part is a remix of Erwin's Losmandy Clamp, slightly modified to provide a tighter fit for Celestron CGE dovetails. A printable knob is included to make mounting the clamp easier. The larger part in the print is unmodified, so if you…
Roger Penrose, awarded the Nobel Prize in 2020 for Physics for his work on black hole formation, is also well known for his discovery of Penrose Tiles. Penrose Tiles are aperiodic over an infinite plane, unique in geometry. This fun soap…
Remix of Flascherl's blade box to be just a bit deeper and store metal cutting blades.
This little knob converts an M6 bolt into a finger-adjustable bolt, eschewing the need for a finicky Allen wrench but still keeping the head available for secure tightening. Simply thread an M6 bolt of your choosing into the hole, with a…
This is a simple 3d printed replacement handle for a cheesegrater my mom loves. I can't live without her cooking, so this is my attempt to keep the italian dishes coming. Printed in PLA, although a dishwasher safe plastic may be better.…
My skull from a scan taken in 2020! There is some damage, due to fungal sinus issues. All internal structure is still in the model, so you can cut it open and see where the bones inside the skull are. I printed on a resin printer with…
This 3D printed push-style mirror cell will hold a 6" telescope mirror. The mirror is held by three or six mirror clips that are secured with M3 heat set inserts. The pull screws are 3/16th"-24 screws with springs and wingnuts. The mirror…
This finderscope is designed to fit Orion telescopes. The part can be printed in place with no supports by laying the back panel flat to the print bed. Use PETG filament so that the part doesn't melt in direct sunlight.
This mounting bracket allows you to mount an Orion Guidescope to any Vixen dovetail (43 mm max width). Print in place with PETG and use M3 screws/knobs to secure your guidescope in place.
About The Project The RASA telescope design presents both advantages and disadvantages. One of the most notable is that you can't install a filter wheel into your lightpath! The Starizona filter drawer solved my filter issue quite nicely.…
Non Printed Parts: 3x 6mm Cylindrical Magnets 1x Pen Spring The cylinder works on its own if needed, but is equal in functionality to the original if properly assembled. You need to push the plunger into the center hole of the cylinder,…
That's right. You can 3D print a working Ronchi ruler. About the Model This model is a Ronchi plate designed to work with the Stellafane Foucault-Ronchi Testing Stand slide holder developed by user Hack_n_Splice . The grating consists of…
Holds hole saws up to 2.5" in diameter. There is enough room for two sets of saws as well, so if your saws don't nest in a single stack, you can nest them in two stacks. The center bit fits in the center, holding the stack together. Print…
These simple plugs can be used when you inevitably drop the plastic plugs that came with your telescope in the observing field, never to be seen again. Print out a few, and be the most beloved astronomer at the star party when others make…
This simple model can be used to plug a hole before spraying paint. The plastic plugs will stick in holes without adhesive or tape, saving time on complicated masking jobs. Print in PLA if you only need a few to save the enviroment, or…
This simple print holds a mirror vertically. Fine details are not necessary on this print; you can go very fast with the right settings. Printed with .28mm layers and 15% infill on an Ender 3 V2 with Black PLA in just 5 hours. If this…
This is a solar filter for the Orion Starblast 6i telescope. The design can be printed in place with no supports, and uses compliant mechanisms to secure itself into the tube. Also, there is a printable case for this filter, designed with…
This simple model is a 2mm light slit, designed to be printed with an Ender 3. The part is 13x6x17.7 cm, and can easily block light from a smartphone flashlight or LED to create a thin sheet of light.
This simple cap can be printed on most printers, including my Ender 3. The cover is a few mm loose so that felt pads can be adhered to the inside, providing friction to hold it in place. Please enjoy!
This telescope cover is tested and designed for the RASA 8 inch telescope. This can be printed on smaller beds by angling the part and using supports. Due to the size, the Ender 3 needs to have the part at an angle; the CR-10 can print…
Why print this? The safety shower drainer is a simple print that clips onto your shower head with quick-release rockers, allowing you to redirect the flow into a hose and wherever the drain is. Often, lab safety showers were not an…
This is a simple remix of the original fan stir plate using my own 9-bladed fan, smaller magnets, and a proper 12V barrel jack connector. Magnets are 6mm diameter, and can be found on amazon . Superglue the magnets for security.
This model fits standard Kimwipe boxes, as well as push-to-dispense alcohol bottles and the modular tape system. Gridfinity allows the whole organizer to fit your existing gridfinite organization scheme. The modular tape system has been…
I use glass Petri dishes for my work, so that I can reduce my plastic waste in the lab. Unfortunately, my glass dishes are not vented. This is a problem when I need air exchange, like crystal growing or fungi culturing. To upgrade my…
This remix of Georg's spherometer accommodates larger shafts, like the Pittsburgh dial indicator. I've made the inner hole a bit wider, and made the height taller to accommodate the longer shaft and improve balance. All fasteners are M3.…
Remix of the Wacom tablet holder by alexberkowitz for my slightly larger tablet. Works exactly the same.
Laser Diode Stand This simple stand holds a 5v laser diode in place, with a simple hinge for up/down positioning. A cable clip on the base protects soldered joints on cables, and mounting holes on the front can be used for securing cables…
This is a DIY bolt-on lamp for microscopes. Three LEDs and a potentiometer illuminate the top of a slide. The print is bolted to the microscope neck, so that the LEDs point down onto the slide. Parts: Resistor Potentiometer Barrel Jack 3…
This drawer fits into most drawer cabinets. Size is 149x31x71 mm.
This simple gear puller allows you to remove stubborn gears from motor shafts using an M4 bolt and a matching M4 Nut.
This is a simple stick-on curve that can be use with JimB's right angle sanding block. The curve is shallow enough that a sheet of sandpaper still easily fits. This is simply an add-on print, make sure you print the original first.…
This was originally designed to solve the problem of owning very few power tools while building the secondary cage for my new 16" Dobsonian telescope. Rather than buying a miter saw and drill press, I was able to cut my dowels to length…
3D printed data table, designed with the printable contest in mind. You can record your success and fail rate with prints (or anything else, for that matter) to watch yourself improve over time. Be the best printer you can be! Spraying…
End up buying a specialty mini tap, only to realize your normal tap handles can't hold it? Print this tap handle! The square hole securely holds a 2.7mm square tap, commonly seen on miniature taps. Use a sturdy plastic and 5 shells, so…
This allows you to put a Picatinny rail onto any 1.25" dowel rod. I use mine for attaching a red dot sight to my dobsonian telescope. To complete the rail, use four M3 heat set inserts. Then, use four 40 mm M3 bolts to connect the upper…
To wszystkie aktualnie dostępne wyniki.
