Liczymy pasujące modele…
similar deflectors are available for sale but not in my country and for a (in my opinion) much to high price so i made some myself. Haven't tested them yet, this is the first prototype. I already found things to change so be warned: this…
Höhenausgleich für das Nähen dicken Stoffes damit der Nähfuß nicht so stark kippt und leichter auf den Stoff fährt. Die beiden Teilen klippen zusammen. Height compensation for sewing thick fabric so that the presser foot does not tilt so…
Simple dual holder for kitchenaid attachments/tools with two 5mm holes for screws
Quad Lock compatible base for 32mm diameter round things, like bike stems, etc. and mounting via cableties. the hole is sized for M4 threaded inserts, original Quad Lock uses M5. Might design other diameters too(like 25mm), feel free to…
my take on a not yet available waste container for the babylock acclaim. It doesn't fit perfectly but it sure does work.
simple air guide for mounting on the original windshield holder. May help with booming wind noise by rear ventilation of the windshield. Due to simpler printability, the part must be adjusted to the curve after printing using a hot air…
Indicator/blinker adapter for the Moto guzzi V7 III for when you want to install aftermarket indicators with M8 Mounting stem. The “recessed” model has, as the name suggests, a small recess to hide the edge on the indicator base. This…
my old quadlock suction windscreen holder didn't quite fit our new renault zoe so i made this intermediate part which mates with the fake vents behind the centerscreen and the gimbal head of the quadlock holder. i made different sizes of…
wanted a discreet quick release for the windshield of my V85TT, so i made one. It doesn't really get smaller than this without sacrificing practicability. A M6x40/50 hex head screw is required Print in PETG or ASA, the dust cap could also…
Wanted something to mount my Sigma Rox with the infamous quarterlock on a strap, e.g. on a backpack, so i took the best working interface(designed by Tim Angus) and designed the strap part around it.
originally the strut bearing of the Renault Zoe lives in a "hole" where, over time, dirt and water gets collected which might be bad for the strut bearing and shorten its lifetime. So i designed a cap which should prevent dirt and water…
Wanted to be able to mount magnetic bags on the luggage rack of my V85TT so i made this, since all aftermarket are aluminium and mostly hideous. Got mine lasered out of 2,5mm steel. Did the bent on the front section myself aswell as the…
small thingy to keep the flap of the Makita DLM382 open when mowing without the bag. Helps especially when the grass has gotten a bit too high(ask me how i know) 04.06.2023: had some problems with clogging so there is now a newer version…
Sold on the internet for 30€ or so, which i think is a ripoff. So i designed it myself so you can print it if you want such a thing. Feel free to modify it for your need Designed for 25mm round stock, bolt on with 4 M4x20mm hex bolts and…
didn't like the valve nut on the curved rim, but without it the valves rattled quite a bit inside the valve-bore. So i made washer that perfectly adopts to the curvature of the rim and since i was already there i made it “aero”…
shorter windshield mounting points for the Moto guzzi V85 TT. Especially usefull when using the Gimpo Garage Ramper GPS holder as it applies extra 5mm spacing between the mounting points. Picture 2 shows the spacing with the original…
i wanted to use existing SW-Motech Legend Gear side-panniers but there are no fitting racks for the BTM Wildfire on the market yet. So i made my own. Disclaimer: these need to be strong! Really, really strong! Using PC-CF wasn't enough on…
wanted to open my garage door without fumbeling in my pocket for the garage door opener. So i automated my garage, integrated it into home assistant and coupled it with a Shelly BLU Button Tough. v2 now 45° rotated with stronger hooks and…
Usb power supply module enclosure, commonly found on ebay( https://www.ebay.de/itm/353963725704?hash=item5269e1d388:g:25MAAOSwQ9xceefy ), for mounting on handlebars. I tried my best to cast the module in the case with heat conductive…
Leaves were getting inside my garage through the open ventilation holes at the top of the roof so i made these fillers. Printed with no top and bottom layer and hexagonal infill to still allow for ventilation while (hopefully) keeping the…
This is just a different interface “spring” with a quadlock-style mounting interface. Use all other arts from the original model. Since this is the best handlebar mount i know of i wanted to use it on my motorcycle too, even though this…
simple modular spool holder i designed to support itself as my drybox is not that rigid. uses 28mm round stock as part of the structure and for the spool-shafts. As i used wooden round stock there are countersunk holes for wood screws.…
adapter rings for the Sigma Overclamp Butler often used with the sigma Rox cycling computers. there was no 26mm adapter included so i made one for my wife's roadbike. The cutout is much wider than on the original so you can route your…
simple protective jaw for the vice. For when you want to clamp fragile parts. needs to be printed in TPU for it to work, with the amount of infill you can adapt the hardness to your needs. Works fine for me with 20% infill.
collar/conduct to seal/close down the hole where the motorcable and brake line leaves the framebox. Print in TPU, the more flexibe the better. Installation might be fiddly
Covers for the BTM Wildfires battery connector, both male and female side, to prevent dust, dirt or even water from getting in the connector while the battery isn’t plugged in. The cover on the battery certainly isn’t waterproof, while…
Keyhanger derived from the “WILDFIRE” badge on the BTM Wildfire Scale to your liking, the “print” file is what worked best for me with a 0,6mm nozzle
Created this mount for increased splashwater-protection as the original mounting situtation for the fender did not provide enough. This will hold the fender just above the tire as it is held down on the movable part of the fork and will…
magnetic holder that utilises the empty spaces left and/or right the “seat belt reminder display”. It isn't necessary to modify any original parts as the magnet holder drops in with some additional force. The magnetholder can be mirrored…
print with tpu and secure with zip-tie
4x 20mm for the front ones 2x 35mm for the middle ones and 2 of the remaining for putting over the screws of the brackets print with TPU
To wszystkie aktualnie dostępne wyniki.
