Liczymy pasujące modele…
This is an N-Scale model train viaduct. I built this to be a wall mounted bridge. The bridge section is loosely based on the Vancouver Skytrain. For other components of my rail bridge, look up my profile. There's about 20 different parts…
This is a curve for my system of viaducts. This goes with and other components my printed viaduct system. This section was setup as a cable stay bridge, suspended from my ceiling. The other parts for this are located here:…
This is an N-Scale model train viaduct bracket. I built this to be a wall mounted bridge. The bridge section is loosely based on the Vancouver Skytrain. For other components of my rail bridge, look up my profile. There's about 20…
This is a small square viaduct section built to be wall mounted. This goes with the brackets and other components my printed viaduct system. The support brackets for this are located here:…
Wall bracket to go with my double track viaduct design: https://www.printables.com/model/317054-double-track-viaduct-for-n-scale-trains This section accommodates 2 mainline tracks with Kato's track system and allows for offramps from the…
A turnout viaduct for my N-Scale train viaduct system. This goes with the brackets and other components my printed viaduct system. This turnout accommodates 4 mainline tracks with Kato's track system and allows for offramps from the…
This is a splitting viaduct section built to be wall mounted. This goes with the brackets and other components my printed viaduct system. The support brackets for this are located here:…
A friction fit cable holder for your extension cables. This reuses your empty filament spools and puts them to good use. Just drill a hole on the inside of the spool, and fit the female side of your spool through. I've included 10 and 15…
This is an adaptor for replacing 2x D cells with a single 18650 lithium battery. Just print off and add in a nickel strip for contact. The lithium battery will give a bit higher voltage, so it will likely overdrive the LEDs a little bit.…
Made for a Happymodel Crux3 1S drone. 75mm props. The V7 is the heaviest/beefiest. V1 is pretty light, but also quite weak. Saved myself a few props learning how to fly.
A replacement foot for my knock-off Eames chairs, for when the feet start to get brittle and break. This is for the wireframe bases, some of the knock-offs probably are a little different in size, so if it doesn't snap on, try scaling the…
This is a bracket for an aquarium light that integrates the supports for an aquaponic system. The aquaponics are in a 4" (100mm) PVC pipe that sits above the aquarium, allowing the pump to fail-safe, and requiring minimal setup. The light…
A larger hook for the Ikea Expedit shalf. These go on the thicker exterior pieces of the shelf. Add a strip of electrical tape if you need it to hold on firmer.
This is a grill and feet for the Noctua NF-A20, so you can make a large and very quiet USB powered desk fan. I used this with the Noctua PWM controller. The feet are friction fit. The controller is attached with double sided tape.
This is an anchor block I used to hang my model railroad cable stay bridge. See my other train models for the components they go with.
A smaller hanger for the Ikea Expedit Shelf. Add a a strip of electrical tape for added grip.
A simple cradle so your glass bottles don't roll around in your fridge. Just print 2! Mine are made out of TPU, which works great for traction. There's also a double bottle rack, so you can stack them. See my profile for my other models.
A simple cradle so your glass bottles don't roll around in your fridge. Just print 2! Mine are made out of TPU, which works great for traction. There's also a single bottle rack, so you can stack them. See my profile for my other models.
Make your clip-on aquarium filter quieter with this damper. Print a couple out of TPU and clip them on to the back of your aquarium, then simply slide your filter on over top. Most of the loud buzzing should go away! This was designed to…
This plate lets you mount a Bondtech LGX Lite extruder to a Duet3d Smart Effector as a direct drive. I used 20mm brass standoffs to allow the plate to clear the heatsink. This likely needs an adapter plate to spread out the effector arms.…
This is a collar adapter to make an E26 light string fit the Tivoli Bulb Covers printed at 133%. The collars are sized to allow for the bulb covers clear a 45 mm diameter bulb, and clamp on to a 34mm light base. Do not use this with…
This is an adapter for the Tevo Little Monster to use 80mm spaced magball arms. I paired this with Asyborg's 80mm smart effector plate. Print this out of PETG or other strong plastics. I used CFPETG and it's quite strong. There's two…
This is a simple mount for a 3mm Berd Air pipe, for part cooling. I had to make it because the existing designs wouldn't fit around the wider 80mm effector mount I'm using (Asyborgs 80mm mount). I printed this using TPU, and it does a…
A rack for making cold brew coffee using a reusable coffee filter. Print one of each.
This is a lid for the planter buckets on an Ikea PS2012 sidetable. The sidetable has built in planters and buckets to do in them, but didn't come in with a lid to make the top flat, so I made these lids which resemble buttons.
To wszystkie aktualnie dostępne wyniki.
