Liczymy pasujące modele…
This is a Small wall mounted Tray I created for Chalk. Angled front to allow ease of rolling or sliding items out and countersunk screw holes for a great finish. Print Settings Printer: Sapphire Plus Rafts: No Supports: No Resolution: 200…
The original cover falls off when you decide to look at it and the wind from your blinking eyelashes blows it off. This design uses the metal casing of the mount and the lip of the mount under the scope to hold this cover on. it locates…
Needed to stop my sample line floating up and getting air in it. the included clip is way too small and I could not find a longer version that suited my sump. Could be cut down if too long. Note - Used a Brim as being thin and long was…
Designed this as I could not find a Hippo cutter I liked. Turned out one of my best cutters I have used. Print Settings Rafts: No Supports: No Resolution: 200 Infill: 100 Filament: YoYi PETG Black Category: Kitchen & Dining
Being short and unable to mount a varia to my bike with a saddle bag attached I decided to create the following solution. This uses hardware included in the Varia and topeak kit. this might fit other topeak bags if the mounting system is…
To make it easy to fill a Hanna Checker for sachet tests. This is made to fit the varied openings of the Vials. Prints quickly and smooth. Customized version of https://www.thingiverse.com/thing:1763508 Created with Customizer!…
Remix of https://www.thingiverse.com/thing:1625098 All that is different is the removal of the handle to allow better and faster printing of the cat Print Settings Rafts: No Supports: No Resolution: 200 Infill: 100 Filament: YoYi PETG…
Not finding a good mount for my Sapphire Plus Stock setup I created the following. its slotted for adjusting the height to your suiting. added strength on the corner to increase rigidity and warping in printing to ensure it sits true. X0…
Very Simple but strong holder for ryobi impact driver and Drill. (may work for other items) Will hold with a 5ah battery attached with no issues and fast to print. 4 screw holds add to the rigidity of this mount Print Settings Printer:…
This is my Tiagra spacer for older levers. these are like gold dust to buy and not cheap. tis however is a spacer that will move the lever roughly 1cm nearer to the rider and not compromise wheel removal on wither side. These are not…
This is my Glass holder created for my Sump to hold a 12.5mm (OD) Silicone tube for my Auto Top up. It has 2 dimples to ensure the tube stays put and the push fit clamp will fit many glass sizes. Enjoy. Print Settings Rafts: No Supports:…
Fed up of other float switch holders being a pain to print or not suitable for my setup I designed this. Holds 2 floats in one bracket. if high and low you could run 4 on this setup. Height is easy to adjust with one screw (printed) In…
Asterina Starfish taking over the tank? can't see through the glass? this will help cut down your starfish population without needing to pump water. Made to fit the generic Scrapper kits seen online (amazon, ebay, ETC) Created in 2 parts…
With the new ReefDelete the button is quite stiff. It does indeed get better with age but the small button still digs in to the thumb and you can't always see the light to know its on. This button corrects this with out holding the button…
Here is a simple and strong mount for the BenQ Monitors where the adapter mount non longer works. Used was a plate converter Vesa Plate ( https://www.amazon.co.uk/Goobay-63267-VESA-Adapter-Mount/dp/B00GOI0WD2 ) and 6 x M4 45mm bolts.…
Designed up this mount so that the Direct Drive mount was not needed to be created with supports to add this as part of it. Clears the belts when homed and acts as a cable guide for the included split cable cover. Requires 2 new bolts to…
I created this from scratch based on a similar design to Pikkenix model https://www.thingiverse.com/thing:3418241 However I wanted no cable ties. able to be removed (good if used as a monitor alot of the time) but hold solid. This fits a…
Simple yet useful to not need to make yourself. numbered label tags. built as a 2 layer print at 0.28 to ensure they fit under a hold. I used a sharpie to colour the numbers but you could make the second layer a different colour. stand…
This is a remix of the great 45 degree adapter from Reefindude. Like his more polygons would be nice but it works. As it was set at 90 degrees I added a safety stop to the end so even at 100 if it did slip (and it really won't) it will…
I have an extended waste tube for easy emptying of my skimmer cup. I got annoyed fishing it out of the water every time I wanted to use it. Other skimmers come with clips so I designed this to fit a Curve 6 or NAC 6 cup. Print Settings…
Made to help move sand around the tank with less mess. I am looking at making a larger version but for now here it is. Remove the rubber covers and slide these on. Print Settings Printer: Sapphire Plus Rafts: No Supports: No Resolution:…
With the new ReefDelete the button is quite stiff. It does indeed get better with age but the small button still digs in to the thumb and you can't always see the light to know its on. This button corrects this with out holding the button…
To wszystkie aktualnie dostępne wyniki.
