Wszystkie modele

Dilator for personal hygiene, home medical type device

Saber Tooth Tiger Skull

This is an actual Saber Tooth Tiger skull, with all of its imperfections. One fang is a little longer than the other. I tried printing this in several different positions and found the best way was front teeth down using organic supports.…

Kitchen Sink Organizer, Caddy

My wife requested this design after reviewing many different models and not finding what she wanted. It has loads of room for scrub brushes, sponges, sink parts like stoppers, drain filters etc. I printed this in tough PLA and…

Cable Tie with Loop Lock End - TPU

I looked for this, but didn't find the exact model I wanted, so I made one that works well. I made mine with TPU 85A. The loop-lock at the end is a snug fit, but it does slide through. This is to prevent it from disconnecting from the…

Large bowl popcorn kernel/husk filter

This is my go-to filter to remove all the stuff in my popcorn that I don't want in the bowl. It works with large to small popcorn. Butterfly, mushroom, pipcorn, amish small kernel etc. You won't lose any popcorn, just the un-popped…

Keyholder Shelf

Shelf with keyholder designed to cleanup spaces from keys, phone, wallet etc. This is designed so that no supports are needed. There are 12 hooks for keyrings. This is screw mountable or could be adhered many other ways. Most key holders…

Drawer handle

I made a replacement drawer handle for one that broke off. This requires two screws to mount it into place. The STL file is set for the screw holes to be solid, so there's no infill on that part. I added the fusion file so anyone can…

Compact Toilet Paper Holder (Screw mounted) or Twin Towel Holder

I was looking for a compact toilet paper roll holder that: 1. holds the fat Charmin rolls 2. utilized screws to mount 3. Would fit in a really tight space next to my toilet. Not finding what I was looking for, I designed this and printed…

Cylindrical Canister (storage container)

This was designed to hold my stainless mesh coffee filters when not in use (see photos). It is threaded, so it doesn't easily slip apart. The inner diameter is 76mm, the length is approximately 450mm with both parts together. After…

The Ripper

After scouring the internet for a good box cutter and testing out other models, I set out to create a small box cutter that would allow me to breakdown the massive number of boxes from shipments I go through. I needed something that would…

Magnetic Key Fob Case for vehicles

I designed this magnetic key fob case for my Chevy Equinox, but it should hold most fobs. My fob is larger than many others, however, it can be scaled up if needed. The slide-locking lid works best if you add a little Vaseline or other…

Adams Rite 25-0471-IP End Cap (Hinge) Door Lock - Push Release End Cap HX0471

Warning! Do not attempt to sell these as the original is likely patented. I designed this after seeing they were around $18 each after tax on Amazon. This is an end cap that closely matches the Adams Rite 25-0471 or HX0471. It also has…

Wide-Tipped Vacuum Filter Pleat Tool

This is made for a smaller vacuum, but could easily be re-sized or you could make an adapter. This makes cleaning up your larger pleated filters easy to vacuum out and extend the life of the filter, so it can be used again and again. I…

Exacto Set Cover

I made this for an exacto set I purchased that didn't come with a cover. The original measurements for the lower case are: 39.9mm x 129.5mm x 10.8mm. This is designed to slide over the top so I don't lose any of the blades in the set. I…

Thin vacuum filter pleat tool

This is is similar to my larger version. The larger version is designed for home A/C filter pleats that are large. This version is much smaller made to fit the very thin filter pleats of small filters. The tip where the holes are is 2…