P
Printablesmfraz74
Boat
Printed with default infill within PrusaSlicer of 15% requires supports.
- Pobrania
- 1917
- Polubienia
- 71
- Ocena
- 4,91
Wszystkie modele
Liczymy pasujące modele…
P
Printablesmfraz74
Peugeot Boxer, Fiat Ducato, Citroen Relay (2006-2023) Drink Cup Holder
Printed in black PETG with 0.2mm layer height, 4 walls and 30% infill. I would recommend using PETG as a minimum, for layer height you could go to 0.24. 4 self tapping screws are required per side. Update 10/11/24: Added modified cup…
- Pobrania
- 890
- Polubienia
- 100
- Ocena
- 5
P
Printablesmfraz74
Dolce Gusto Coffee Pod Rack
A space-saving solution to store your Dolce Gusto pods. The main part which I have made in both 165mm and 110mm long can be slotted together with the bottom piece at the bottom of the rack. You can fix the rack with glue or double sided…
- Pobrania
- 168
- Polubienia
- 41
- Ocena
- 5
P
Printablesmfraz74
Case for 0 - 25mm micrometer
Printed with a 0.2mm layer height, allow it to cool fully before moving from the print bed. Carefully close the lid so that it doesn't break.
- Pobrania
- 156
- Polubienia
- 19
- Ocena
- 4,5
P
Printablesmfraz74
Rugged Weather Proof Case for Sonoff SNZB-04P Door/Window Sensor
It can be printed with 0.2mm layer height and with no supports, no need to rotate the models. Remove both the sensor and magnet from their original cases. Keep the screws holding the sensor PCB to the case as they will be used later. Push…
- Pobrania
- 144
- Polubienia
- 13
- Ocena
- 0
P
Printablesmfraz74
Dartboard number ring clip
This should be printed in TPU to make it more impact resistant. I used a 0.16mm layer height, but anything below 0.2mm should be fine. There is a 3.2mm hole for a nail or screw.
- Pobrania
- 134
- Polubienia
- 4
- Ocena
- 0
P
Printablesmfraz74
Cute Mini Octopus with Top Hat and Monocle
In addition to a top hat, someone now wanted an octopus with top had and monocle.
- Pobrania
- 119
- Polubienia
- 24
- Ocena
- 0
P
Printablesmfraz74
Hanging case for Waveshare 8" display
This is a case to hold an 8inch DSI LCD screen from Waveshare with a Raspberry Pi screwed to the back of the screen. There is also provision to hold a BH1750 Light Sensor from Adafruit so that the brightness of the screen will adjust…
- Pobrania
- 87
- Polubienia
- 6
- Ocena
- 0
P
Printablesmfraz74
Ender 3 V2 Neo Mount for V1, V2 & V3 Pi Camera Modules
I tried printing the models on Thingiverse, but they wouldn't fit over the Neo's X axis cover. So I redesigned it so that it picked up with the M3 screws that hold the cover on. I printed all parts with a 0.2mm layer height, supports…
- Pobrania
- 82
- Polubienia
- 7
- Ocena
- 0
P
Printablesmfraz74
ID badge holder with RSA SecurID pocket V3
Print one of the ID holders and the RSA holder. The RSA holder snaps into the ID holder. Printed at 0.2mm layer height in black PLA, you can even have a different colour for each part. To fit the RSA into the holder, remove the ring and…
- Pobrania
- 81
- Polubienia
- 4
- Ocena
- 5
P
Printablesmfraz74
ID badge holder with RSA SecurID pocket
Print both parts in the orientation of the STL files. You will require supports under the lanyard slots and maybe along the centre of the inside of the RSA pocket depending upon your bridge settings. It was printed at 0.2mm layer height…
- Pobrania
- 77
- Polubienia
- 5
- Ocena
- 0
P
Printablesmfraz74
Sonoff RM433 Remote holder
Printed in white PLA with 0.2mm layer height. Pause the print at layer 21 to insert a 6mm X 2mm magnet - make sure you have the correct pole facing up. Update 26/02/21 I've only just realised I uploaded the model without space for the…
- Pobrania
- 64
- Polubienia
- 4
- Ocena
- 0
P
Printablesmfraz74
Memo pad holder with Pen Storage
Memo pad holder for pads up to 90mm square with space for 13 pens or pencils. I printed it with a 0.2mm layer height and 15% infill, but you could go for 0.24 or 0.28 layer height.
- Pobrania
- 63
- Polubienia
- 10
- Ocena
- 0
P
Printablesmfraz74
List stencil
I've made a smaller version of Kai's that is 150mm long and will fit on an Ender 2 Pro. Also the boxes are 5mm square.
- Pobrania
- 60
- Polubienia
- 13
- Ocena
- 0
P
Printablesmfraz74
LED light strip for Ender 3 V2 Neo
This is a LED holder for the Ender 3 V2 Neo that works for LED strips up to 10mm width. Printed at 0.2mm layer height with 15% infill. Supports required for the joining spigots. Print 2 of the strip mounts and either 2 or 3 strip mount…
- Pobrania
- 54
- Polubienia
- 6
- Ocena
- 0
P
Printablesmfraz74
Sink plug holder
Simple holder for a bathroom sink plug. Requires 2 22mm round button suction cups. Printed with support on Ender 2 Pro 0.16mm layer. Update 23/5/4: I've refined the design to make it more curved. Update 25/11/30: Complete redesign, no…
- Pobrania
- 49
- Polubienia
- 9
- Ocena
- 0
P
Printablesmfraz74
Raspberry Pi Squeezebox case
Case designed to fit a Raspberry Pi, touch screen display and speakers. This is the display I have used https://www.amazon.co.uk/gp/product/B07KJBCNS8/ The speakers - https://shop.pimoroni.com/products/mini-speaker-4-3w Speaker Bonnet -…
- Pobrania
- 48
- Polubienia
- 6
- Ocena
- 0
P
Printablesmfraz74
Raspberry Pi Squeezebox case V3
Case designed to fit a Raspberry Pi, touch screen display and speakers. This is the display I have used https://www.amazon.co.uk/gp/product/B07KJBCNS8/ The speakers - https://shop.pimoroni.com/products/5w-4-ohm-65mm-full-range-speaker…
- Pobrania
- 44
- Polubienia
- 7
- Ocena
- 0
P
Printablesmfraz74
Cleco Side Grip Clamp holder
Printed these at 0.16mm layer height with a 0.4mm nozzle. I've now added text to the bottom face to say what should be on each holder. Update 26/06/21: I've now included a FreeCAD file so that you can change the number you want to hold by…
- Pobrania
- 42
- Polubienia
- 12
- Ocena
- 5
P
Printablesmfraz74
Stand for Amazon Echo Dot 4
I printed this with the top on the print bed with supports. 0.4mm head & 0.16mm layer.
- Pobrania
- 40
- Polubienia
- 10
- Ocena
- 0
P
Printablesmfraz74
Wall Wart/PSU Cable Tidy Remix
A remix of @Spudd78_648739 which was a remix of @DavidJ_250853 's Wall Wart/PSU Cable Tidy to make it print without need of supports and now with closer fitting plug slots. It is currently for UK BS 1363 (IEC Type G) plugs. I can add…
- Pobrania
- 34
- Polubienia
- 2
- Ocena
- 0
P
Printablesmfraz74
Raspberry Pi Squeezebox case v 2.0
Case designed to fit a Raspberry Pi, touch screen display and speakers. This is the display I have used https://www.amazon.co.uk/gp/product/B07KJBCNS8/ The speakers - https://shop.pimoroni.com/products/5w-4-ohm-65mm-full-range-speaker…
- Pobrania
- 33
- Polubienia
- 8
- Ocena
- 0
P
Printablesmfraz74
2 Cases for Adafruit 0.56" 7 segment display and backpack
This is for the older backpacks that don't have the STEMMA connectors. The case has 2 3mm holes for mounting, if it is printed with support the unused one can be left with support material to blank it off. Hinges require M3 brass inserts…
- Pobrania
- 30
- Polubienia
- 2
- Ocena
- 0
P
Printablesmfraz74
Small size tap holder
This is just the holder model for small tap sets such as this one. You will still need the base and lid from the original model.
- Pobrania
- 29
- Polubienia
- 4
- Ocena
- 0
P
Printablesmfraz74
Print in place hinged bracket for Raspberry Pi Cameras
I've altered my original design by changing the hinge to make it print in place and a variant for the v2.1 camera.
- Pobrania
- 22
- Polubienia
- 3
- Ocena
- 0
P
Printablesmfraz74
Adafruit USB Type C Power Delivery Dummy Cases
There are two different cases, one is for Adafruit USB Type C Power Delivery Dummy - I2C or Switchable - HUSB238 - STEMMA QT / Qwiic and the other for Adafruit USB Type C Power Delivery Dummy Breakout - I2C or Fixed - HUSB238 Print in the…
- Pobrania
- 17
- Polubienia
- 1
- Ocena
- 0
P
Printablesmfraz74
22x31mm NFC for Rolodex-Style Card Holder
Printed at 0.12mm layer height with a 2mm brim. No support required.
- Pobrania
- 15
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
40mm Fan Guard with light support
I printed this in PLA with a 0.2mm layer height. The mounting holes take M3 countersink machine screws. The googly eye supports are 12mm diameter. For the Adafruit sequin support (https://learn.adafruit.com/adafruit-led-sequins) I…
- Pobrania
- 14
- Polubienia
- 2
- Ocena
- 0
P
Printablesmfraz74
ID badge holder with RSA SecurID pocket V2
Print both parts in the orientation of the STL files. If you print with a 0.2mm layer height and use PrusaSlicer or OrcaSlicer, you will not require any supports as there is a bridging layer. Once printed, remove the bridging material…
- Pobrania
- 14
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
Hanger for bookcase
A hanger that clips over the sides and shelf of an Ikea Gersby bookcase or other bookcases that have a 15mm shelf. There are left handed and right handed hangers. Printed with a 0.2mm layer height. No supports required. Update 25/01/25:…
- Pobrania
- 13
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
Kingroon Electric Vac Pump Charger
Printed at 0.2mm layer height 15% infill. No supports required. All screw holes are M3, recommend tapping them before using. You will require a USB Type B Micro B Male Plug Receptacle Breakout Module Board such as this one from eBay a…
- Pobrania
- 13
- Polubienia
- 1
- Ocena
- 0
P
Printablesmfraz74
CatEye VOLT400XC mount
Printed with 0.2mm layer height. Rotate so that it lays flat on the bed, support required for hole. Remove strap from bike light and attach to mount. Use a cable tie (zip tie) to attach it to the handlebars. Update 25/01/25: Made the…
- Pobrania
- 11
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
10Zig thin client stand
I needed something that would allow me to have the thin client horizontally on the desk. This was printed at 0.2mm layer height, but you could go for 0.24mm or more. Remove the existing stand from the base by unscrewing it and then place…
- Pobrania
- 11
- Polubienia
- 1
- Ocena
- 0
P
Printablesmfraz74
Swiming Pool Hose Adaptor
Adaptor to allow a standard hose to drain a swimming pool.
- Pobrania
- 10
- Polubienia
- 1
- Ocena
- 5
P
Printablesmfraz74
Mirage Pop Out Pencil Case replacement door
This is a replacement pencil sharpener door for a Mirage Pop Out Pencil Case from Smiggle. Printed with a layer height of 0.12mm and 25% infill. Supports required for the latch and maybe for the hinge.
- Pobrania
- 10
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
CP Desoutter Button Cap
Button cap to replace a broken button on Desuoutter air tools.
- Pobrania
- 9
- Polubienia
- 1
- Ocena
- 0
P
Printablesmfraz74
Hook for Salter 1035 scales
Print at either 0.16 or 0.12 layer height. Supports will probably be required.
- Pobrania
- 9
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
Raspberry Pi Osoyoo 7" DSI Touch Screen Stand
I decided to replace my Raspberry Pi Touchscreen with one from Osoyoo as it only required the ribbon cable between display and Pi for use with my Lyrion Player. You need to print both legs one left and one right. It needs four M3x12…
- Pobrania
- 8
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
Yankee Candle wax melt dispenser
This is a Yankee Candle wax melt dispenser to store 3 - 6 wax melts. Printed in white PLA with a 0.2mm layer height. No supports required. I have included the original FCStd file if you want to make some changes.
- Pobrania
- 5
- Polubienia
- 0
- Ocena
- 0
P
Printablesmfraz74
Replacement foot for patio lounge set
This is a replacement foot for the New Hampshire Transformer garden set from The Range. Print at 0.20mm layer height in a material suitable for outdoor use such as PETG, I've also used TPU-CF which gives it a bit more flexibility. No…
- Pobrania
- 0
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.