Liczymy pasujące modele…
This is a configurable riser/top-hat for the SOVOL SV08 printer. In its basic form, it has four corner pieces (labeled) and four vented panels. The panels include an optional slider to open and close the vents. The optional/replacement…
I saw a friend using a tool for his Elegoo printer to level the print bed. I decided to make something similar to it for my K1Max. This is a simple tool that helps in leveling the K1 series print bed. It hangs from the upper X carriage…
This holder can hold up to two print beds and a large glass enclosure lid for SOVOL SV08. It is mounted on the side of the printer using two M3 x 10 mm screws on each side. ***UPDATE *** There were requests for a holder that holds more…
I liked the simplicity and functionality of Jose's design. But I wanted a bit more organization. One compartment for taller tools (like nozzle plunger), one for shorter tools (like filament cutter), and one for putting screws and parts…
I wanted to find a way to store the top glass door of the Sovol SV08 OEM enclosure. It attaches to the side of the SV08 enclosure using four M3 x 10 (or 12mm) screws. To give it some strength, I printed it with three walls and four top…
I have Microwswiss Flowtech hotends on all of my printers, and I have a collection of Brass, CM2, CHT, CM2-CHT, and Diamond Flowtech nozzles. I made these cases to organize each printer's supplies. There are two versions, small and large.…
The official enclosure for the Sovol SV08 exhaust fan has a flimsy, thin foam filter. I wanted to use either an activated carbon filter or a HEPA filter. I designed a holder that accommodates these filters. I printed it with PETG, and it…
***NOTE: This mount only works for Phaetus Rapido 2 Plus UHF This is the one: https://www.phaetus.com/en-us/products/rapido-plus-hotend-2?variant=45199405121813 You need the black one. It comes with a PT1000 thermistor and a maximum…
I wanted a neat, out-of-the-way, low-profile mount to attach the MEAN WELL LRS-350-24 PSU to the bottom of my 3D printer. I wanted it to attach to two DIN rails, without causing a counter-leaver effect. I printed this with PETG to provide…
I recently upgraded to DXC extruder on my K1max. This extruder has a filament sensor, and the wires are attached to the MCU from the back of the toolhead. In addition, the motor connection to this extruder requires an extension cable…
I liked the riser feet for SV08 by @Max_206949. However, I decided to reduce the vibration caused by SV08 and wanted HULA vibration-dampening feet for SV08. I had an excellent result with HULA system sold by VoxelPLA. So I remixed these…
I needed a nice mount for CoPrint KCM to be close enough to the extruders that I could use the shorter connector cables and also tidy things up. So I used CoPrint's published CAD file for KCM, quickly put something together, and printed…
I adapted the excellent Feet riser/extender made by @Max_206949 https://www.printables.com/model/1052416-sovol-sv08-feet-module to use Creality Shock Absorbing Silicone Pads:…
I've seen some tool trays that fit under the printer. However, the way my printer is situated, if I pull it out to access some tools, it might fall off the edge of the table. Previously, I used a small tool tray, which was anchored to one…
I needed a filament spool holder that could accommodate 4 spools for my CoPrint KCM system. The feed should be vertical into the 4 KCM extruders. I purchased a Yoopai spool holder:…
After installing the OEM enclosure on my SV08 Max, I noticed that the back half of the top cover is empty and screwed in. I designed this quick rack using 1/2 inch PVC pipe I had at home, left over from another project. The two ends are…
This is a mount for SSR units such as: https://www.amazon.com/dp/B005T7XENO?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_5 It accommodates a heatsink such as:…
To wszystkie aktualnie dostępne wyniki.
