Liczymy pasujące modele…
Fully customisable and printable folding propeller set. Including a hub and a spinner. This is based on the 'Parametric Folding Propeller Generator' by @BouncyMonkey ( https://www.thingiverse.com/thing:3506762 ) Also the Polyline code…
This is a minimalistic Stick on Laptop feet. This stays on the laptop all the time and folds away to carry. Some assembly is required. You would need to use a 2mm dia(approx.) wire to make the hinge. I use bicycle spoke wire as hinges.…
This is a simple tilt mechanism that i designed for a VTOL aircraft that I am building. This design uses a standard 40g servo. I used the HXT5010. additionally it uses a 685 bearing. I know most here would consider it a non-standard…
This is a simple antenna protector that I designed. The primary objective was to keep it light and very strong. I designed it for the AOMWAY 4-leaf clover antenna, but should fit all 5.8ghz antennae which are the same style. There is a…
This is a printable LM8UU equivalent bearing. It is used in place of a conventional steel LM8UU. I designed it so that it can be used as a replacement for Ultimaker style sintered-brass bushings. This is also me trying to place a concept…
Very often once you have the entire power/drive train calculated and ironed out for max efficiency, you do not get the perfectly sized folding prop. Here I try to explore the concept of having a kit that transforms any prop to a folding…
This is just a simple remix with minor enhancements. I found this method to be the most reliable and yet cheapest solution for auto-bed leveling in the Ender-3. The M48 command on Marlin (probe repeat-ability test) gives the following…
just some small changes done to the openScad file: ...so that the created plaque can comply with different standards. support pads can be added for easier printing. 'index' corner cut to gauge correct orientation. the dot shape can be…
A simple mount for the inexpensive L80 module from Quectel. This GPS module is based on the mediatek MTK location engine. Find more details here: https://www.quectel.com/UploadImage/Downlad/L80_Hardware_Design_V1.1.pdf The mount makes…
These are Mr. Steele V2 style pants for the RCX2207 motors from MyRCMart. The rcx2207 comes with the winding pretty exposed (of course its a bottom-less design), and I wanted to protect them a bit. Print Settings Printer: Prusa i3 Rafts:…
Simple modification to fit on a frame with a flat top plate Print Settings Printer Brand: Prusa Printer: Prusa Clone **Rafts:** No Supports: Doesn't Matter **Resolution:** 0.2mm Infill: 20 Category: R/C Vehicles
The stock FPV camera mounting option does not go beyond approx 10degrees. This is a mount design that lets you mount it at 20 and 30 degrees. Print Settings Printer: Prusa i3 Rework Rafts: Doesn't Matter **Supports:** No Resolution: 0.2mm…
This is a quick development of a neck strap balancer for the Devo 7E. I am sure people can use it for other radios. To print(I print with Repetier-Host): 1.Rotate the part to lay it flat (-90deg X-axis) Create a copy of the part. Mirror…
This is a an attempt to build a simple dualstrusion mechanism, using a single motor and single hot end. The idea was to provide with a simple upgrade possibility to many people who have a single extrusion setup. And keeping the cost low…
This is a simple XY carriage for a custom H-Bot my friend was building. (I just designed some printed parts for him). This optimizes the print height to the maximum (as can be done from the XY carriage perspective) The Fan duct is…
This is a simple Y carriage for a custom H-Bot my friend was building. (I just designed some printed parts for him). This has mount points for the 2 pulleys required for a Hbot. Uses: LM8UU bearings 8mm smooth rods 624 bearings with…
There are a lot of part cooler designs out there but most I came across were with some major cyclic shortcomings. Like: Some are brilliant/effective designs but they are complicated and need cooling and supports to prints. Others are…
To wszystkie aktualnie dostępne wyniki.
