P
PrintablesSimmer65
Spray Bottle Hanger/Wall Mount
A little rack for holding spray bottles in the garage. It's held to the wall with #8 screws. I printed it in PETG with no supports.
- Pobrania
- 3074
- Polubienia
- 1264
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesSimmer65
Router Bit Holder
A holder for router router bits with a ¼" shank. There are 4 mounting holes. I attached mine up and out of the way with (4) #10 wood screws. Update on 12/28/2025: Added two new versions for 1/2" router bits. The shank hole diameters are…
- Pobrania
- 1371
- Polubienia
- 352
- Ocena
- 4,92
P
PrintablesSimmer65
Network Cable Tag
This print will help you make sense of your network cables. It bends into shape. The spring back keeps in in place on the cable. There a spot to put a printed label. The holes were sized for a wire with a diameter of ¼" (6.3mm). I…
- Pobrania
- 954
- Polubienia
- 441
- Ocena
- 5
P
PrintablesSimmer65
Putty Knife
I created this putty knife to spread wood filler on a flat 3D printed surface that I want to look flawless. It is 5-¼" long with a hole in the end to hand it on a nail. It requires no supports or brim. Mine was printed in PETG, but PLA…
- Pobrania
- 378
- Polubienia
- 13
- Ocena
- 5
P
PrintablesSimmer65
Table Edge Wire Organizers
Two different sizes for wire organizers. One fits snuggly on a desk that is .65" thick. The other is made for a table that is 0.8" thick. They hold my USB cables off the floor so I don't run over them with my office chair.
- Pobrania
- 292
- Polubienia
- 154
- Ocena
- 5
P
PrintablesSimmer65
Soccer Ball Stand
A simple stand for a soccer ball with custom supports
- Pobrania
- 237
- Polubienia
- 20
- Ocena
- 5
P
PrintablesSimmer65
Network Cable Combs
These cable combs were printed at the end of my filament spool. With a few wraps around the spool left, I printed several of the combs to try to make some sense of the spaghetti in my network closet. There are three different size because…
- Pobrania
- 193
- Polubienia
- 61
- Ocena
- 5
P
PrintablesSimmer65
Swing-Out Screwdriver Arm for 1/4" Pegboard – No Headroom Needed
Hole-style racks waste pegboard space A screwdriver rack with holes holds drivers better than one with slots, because they can't slide out the front. But you have to lift each driver straight up to get it out of its hole. That means…
- Pobrania
- 146
- Polubienia
- 80
- Ocena
- 5
P
PrintablesSimmer65
Network Cable Combs, version 2
This version of the cable combs is easier to snap into place. They clip onto network cables that measure ¼" diameter. There are two different pitches. The .45" pitch keeps the cables close together. The .60" pitch spaces out the cables…
- Pobrania
- 131
- Polubienia
- 31
- Ocena
- 5
P
PrintablesSimmer65
4x4 Speed Square
A handy 4x4 speed square. One flange is 3/8" of an inch to find the center of a ¾" board. The opposite flange is ¼" to find the center of a ½" board. Mount for this speed square:…
- Pobrania
- 128
- Polubienia
- 11
- Ocena
- 5
P
PrintablesSimmer65
Heavy Duty Wall Hook resized
A heavy duty bracket that requires no supports.
- Pobrania
- 127
- Polubienia
- 9
- Ocena
- 5
P
PrintablesSimmer65
Altoid Tin Organizer
I started off making a rack for some Altoid tins I had collected over the years. I soon ran out of tins. So I printed some. Then I realized that a package of screws from Home Depot holds just a little too many screws to fit in the tins.…
- Pobrania
- 118
- Polubienia
- 26
- Ocena
- 0
P
PrintablesSimmer65
Topographical Map Of Pennsylvania
I made this 3D print with old “wood” filled PLA. It was extremely stringy…but I like it.
- Pobrania
- 104
- Polubienia
- 7
- Ocena
- 5
P
PrintablesSimmer65
Ball Pin Case
A small case to hold pins to blow up a ball. The top screws on.
- Pobrania
- 103
- Polubienia
- 32
- Ocena
- 0
P
PrintablesSimmer65
Spray Can Rack
Wall mounted hooks to hold spray cans horizontally. Mounts with two #8 screws.
- Pobrania
- 96
- Polubienia
- 37
- Ocena
- 5
P
PrintablesSimmer65
Wall Mounted Spray Can Basket
In an effort to organize the garage, I printed this basket to hold spray cans. It holds two cans. I printed it in PETG with no supports or brim. The walls are thin, so infill is not needed.
- Pobrania
- 92
- Polubienia
- 7
- Ocena
- 4,5
P
PrintablesSimmer65
USB Organizer
This organizer takes about 30 minutes to print with the default slicer settings. I printed it in orange PETG (because it was already in the printer). It holds 5 thumbdrives. I designed it Blender and exported it as an STL file.…
- Pobrania
- 77
- Polubienia
- 13
- Ocena
- 0
P
PrintablesSimmer65
German Shepard Magnet
A German shepherd refrigerator magnet. 4" x 2.93" x 0.5". A ½" x 0.20" magnet can be glued into the back.
- Pobrania
- 73
- Polubienia
- 11
- Ocena
- 0
P
PrintablesSimmer65
Basset Hound Magnet
A basset hound magnet for your refrigerator. 2.31" x 1.7" x .25" Cavity in the back for a ½" x 0.20" magnet that can be glued into place.
- Pobrania
- 64
- Polubienia
- 12
- Ocena
- 5
P
PrintablesSimmer65
Bottle Cap Opener
It's a bottle cap that removes bottle caps. Prints with no supports. Add to 10mm x 3mm magnets to stick it to the fridge. This design requires a bottle opener insert kit which is available at Amazon.…
- Pobrania
- 60
- Polubienia
- 8
- Ocena
- 0
P
PrintablesSimmer65
Gage Block Set
A set of gage blocks. 2 of each size. From ½" to 1/64". Plus an organizing box.
- Pobrania
- 57
- Polubienia
- 6
- Ocena
- 0
P
PrintablesSimmer65
Loupe Holder
Some times you need more than two hands. This holder is designed to hold a loupe and adjust it to just the right height for good vision. The base comes with flat spots if you want to clamp it to the table.
- Pobrania
- 52
- Polubienia
- 13
- Ocena
- 0
P
PrintablesSimmer65
Tarp Bolt and Nut
I made a handful of these nuts and bolts to turn a simple tarp into a fitted cover to protect my deck furniture during the winter months.
- Pobrania
- 46
- Polubienia
- 12
- Ocena
- 5
P
PrintablesSimmer65
1/4" Tube Sharkbite Removal Tool
In the middle of repairing the office watercooler, I need this little tool to remove a Sharkbite fitting. I printed mine in carbon fiber PLA.
- Pobrania
- 42
- Polubienia
- 7
- Ocena
- 0
P
PrintablesSimmer65
Lawn Mower Knob
A replacement knob for a John Deere lawnmower. The carriage bolt goes through the handle and the knob. Held in place with a ¼"-20 machine nut. I printed it a 45 degrees so the layers lines aren't on the same plane as the shear forces.
- Pobrania
- 37
- Polubienia
- 9
- Ocena
- 0
P
PrintablesSimmer65
Router Bushing Organizer
A rack that holds up to 10 router bushings. Printed in PLA in three parts. The dovetail connection needs no glue or fasteners. The rack is held to my bench with 4 wood screws.
- Pobrania
- 32
- Polubienia
- 9
- Ocena
- 0
P
PrintablesSimmer65
Staple Gun Wall Mount
Organize your shop without putting your tools out of reach. With my settings, it took just under an hour to print and took 18.3 g of filament. This piece is .75" wide by 3.25" tall by 1.3" wide. I printed it in PETG, but whatever you have…
- Pobrania
- 24
- Polubienia
- 5
- Ocena
- 0
P
PrintablesSimmer65
Spray Bottle Wall Mount
This mount holds a spray bottle up to 3-3/4" in diameter. It can be printed with no supports. It measures 3.94" high and has two mounting thru holes. I printed mine in PLA with 10% infill and 3 perimeter layers.
- Pobrania
- 24
- Polubienia
- 7
- Ocena
- 0
P
PrintablesSimmer65
Stackable Tic Tac Rack
Empty Tic Tac containers can be used effectively to organize small parts. I designed a small, stackable rack to keep them organized. It prints with no supports. I printed mine in PLA. NOTE: Tic Tacs come in two sizes. This fits the…
- Pobrania
- 23
- Polubienia
- 8
- Ocena
- 0
P
PrintablesSimmer65
4x4 Speed Square Mount
A holder that mounts to my workbench to hold my 4x4 speed square so it's always handy. 4x4 speed square: https://www.printables.com/model/1027198-4x4-speed-square Printed in PLA with 0.30mm DRAFT settings. 15% infill no supports no brim…
- Pobrania
- 20
- Polubienia
- 6
- Ocena
- 0
P
PrintablesSimmer65
Makita Palm Sander Hole Punch
This punch has a straight edge and sharp cones to punch holes into sandpaper on my orbital sander.
- Pobrania
- 19
- Polubienia
- 4
- Ocena
- 0
P
PrintablesSimmer65
Venturi Air Gun Adapter
I created this model for the shop to use with a CNC machine. It extends the reach of my compressed air nozzle so that I can avoid getting coolant on my arms when I spray parts away from the tool. The venturi converts energy from the…
- Pobrania
- 19
- Polubienia
- 11
- Ocena
- 0
P
PrintablesSimmer65
Epoxy & Glue Bottle Holder for 1/4" Pegboard – With 4 Mixing Trays
Both bottles, and something to mix on Two-part epoxy comes in two bottles, and every time you use it you also need something to mix it on. This rack keeps all of that in one spot on the pegboard. The resin and the hardener stand side by…
- Pobrania
- 15
- Polubienia
- 7
- Ocena
- 5
P
PrintablesSimmer65
Cutting Board Drying Pyramids
This is a perfect print when you're nearing the end of your filament spool. I made these for drying my cutting board. I place the cutting board on 4 of them and this allows air to dry the bottom. They stack for compact storage. I modelled…
- Pobrania
- 14
- Polubienia
- 1
- Ocena
- 0
P
PrintablesSimmer65
Hoe Hook
A hanger for a garden hoe. It prints with no supports or brim. I printed it with PLA and 0.3mm layers and 15% infill. The print time was 2-½ hours.
- Pobrania
- 13
- Polubienia
- 3
- Ocena
- 0
P
PrintablesSimmer65
Standing Dog Magnet
A refrigerator magnet of a dog standing on it's hind legs. Cavity for a ½" by 0.20" mganet.
- Pobrania
- 12
- Polubienia
- 1
- Ocena
- 0
P
PrintablesSimmer65
CoreOne Side Holders
6 holders with embedded magnets to hold tools out of the way but close at hand. The magnets I used are 8mm x 3 mm. Print one or print all of them. Each part has 2 embedded magnets except for the bin, which has 4. The magnets are strong…
- Pobrania
- 7
- Polubienia
- 8
- Ocena
- 0
P
PrintablesSimmer65
Tilt-Out Screwdriver Holder for 1/4" Pegboard – Expandable, No Hardware
Tip it forward, pull the driver out A screwdriver rack with holes holds drivers well, because they can't slide out the front. But to get a driver out, you have to lift it straight up until the tip clears the hole. So the board above the…
- Pobrania
- 7
- Polubienia
- 24
- Ocena
- 0
P
PrintablesSimmer65
Coping Saw Holder for 1/4" Pegboard – Drop In, Lift Out
A coping saw takes up a lot of space lying flat The frame is a big open loop with a thin blade strung across it, so a coping saw lying flat on a shelf or bench takes up far more room than its size suggests. I couldn't find a pegboard…
- Pobrania
- 7
- Polubienia
- 5
- Ocena
- 0
P
PrintablesSimmer65
Magnetic Chisel Holder for 1/4" Pegboard – Holds 3, Fits Any Brand
No slots, so any chisel fits Most chisel holders have a slot for each blade, sized for one set: Narex, Stanley, Irwin or Craftsman. If your chisels came from a different set, or you bought them one at a time, they don't fit. This holder…
- Pobrania
- 6
- Polubienia
- 4
- Ocena
- 0
P
PrintablesSimmer65
Channel Lock Pliers Holder for 1/4" Pegboard – Handles Up, Grab and Go
Channel locks don't stay on pegboard hooks Tongue-and-groove pliers (most of us call them channel locks) are long, heavy at the head, and their handles spread apart. Hung on a pair of pegboard hooks, they swing, slide around and drop off…
- Pobrania
- 6
- Polubienia
- 6
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.