Liczymy pasujące modele…
The Midea Portable AC units come with a dual exhaust hose that normally vents in the horizontal direction for a double-hung/sash style window. It includes an adapter to rotate the orientation 90 degrees to vertical for sliding style…
Remix to accept a 9mm drive. Category: Computer
Tronnic's original item makes use of the “After Layer Change” custom g-code to change the temperature between each layer. I create a simple Python script that leverages a comment that gets inserted at each layer change, and will combine…
End brackets for a spool holder, used with 5/8" dowels. Edit: I originally had this listed as 3/4" dowels, as that's the bin I was pulling them from at the hardware store. I think their bin is mis-labeled, as I get 5/8" when I measure…
Updated to include pockets for embedding 6x10mm neodymium magnets in print, in combination with gluing matching magnets to back of switch plate allows easy setup / removal. Two screws in the wall-plate need to be replaced with fillister…
Rebuilt this from the ground up to have a higher resolution STL/3MF exported as the original print had visible facets. Also generated 3MF with multiple parts so that it can be printed multi-color, star and manger are individual parts for…
Wanted a 3D printed phone mount that would fit in the unused coin slot in the dash on my 2014 F150 Lightning. Something that would lock into place easily so it wouldn't pop out, and would be compatible with the standard AMPS hole pattern.…
Remix of @Holspeed excellent Filament Roller Guide, changed to utilize 604 bearings like these from Amazon https://www.amazon.com/gp/product/B01M2CSJE4/ Takes an M4x16 screw to hold the bearing in place. The hole facing the back is 4mm,…
I created this to pull the lm8uu linear bearing out of the carriages on my Monoprice Mini Delta. It also worked well to seat the new bearings by pulling them in. It will probably work for other configurations using lm8uu linear bearings.…
We have a couple of Ames Wrought Iron (design, it's plastic) 2391375NL Hose Reel that we've had pretty good luck with (the online reviews of it don't seem to be favorable though). One of the things we like about is is that the anchor…
I had picked up some Leviton 12-port keystone jack patch panels, and 12-port Monoprice CAT6 patch panels and discovered that the brackets that came with them weren't deep enough to accommodate all the cables behind them. I created this…
I had purchased this base from Amazon https://www.amazon.com/YOUSHARES-Microphone-Adjustable-Interface-Cantilever/dp/B09L88CFBY when the table clamp base for my articulating arm magnifying glass broke. The injection molded base on this…
Simple 3D printed bulb holder to head a hummingbird feeder. I used this lamp socket and cord from Lowes because that's what I could get my hands on same-day Project Source 60-Watt Plastic Turn Knob Lamp Socket, Clear in the Light Sockets…
Printed this on an Ender 3 in eSun PLA 0.24mm Draft in PrusaSlicer with a 0.4mm nozzle @ 210C. Took a short piece of TPU and melted the ends together to create a ring and then clipped these on.
I created this mount to hold my old Galaxy S7 in landscape mode on a GoPro Flex mount with a ¼-20 adapter to use as a web cam with my PrusaXL. Printed this with a 0.32mm layer height and 15% infill in PLA. Mount works best if you slide…
This is the plastic slider piece for the rear window wiper on the 02-06 CR-V, this is the part that lifts the wipe over the gap between the body panel and the rear window when you turn the wiper on and off. This is a wear item and I…
We've been in our house for several years and the bi-fold door in front of the dryer has been a constant problem. If the door is open it blocks the garage door, so if somebody gets something from above the dryer and forget to close it you…
A re-mix of mugbean's Pi Zero W Case to add a mounting point, and extra height to support the addition of Pimoroni's automation phat. I used this case to mound the combined Pi Zero and pHat to my garage door opening. The pHat provides a…
I'm using Reflectix to insulate the underside of my heatbed. I was having problems with the bed warping slightly because the Reflectix was being compressed more on the edges. This support goes under the heatbed to limit the compression.…
!!WARNING!! - Use at your own risk, tolerances are tight and this part could interfere with bed movement. I have a Raspberry Pi with a USB-SDR dongle and RTL433 setup to read AcuRite wireless temp and humidity sensors in my house,…
This is a small shelf I designed with a small “fancy” detail for mounting an Acurite Temp/Humidity sensor on the wall with a medium Command strip that has been slightly cut down in length. The x3 version was for holding 1 Accurite sensor,…
I used 6x3mm neodymium magnets, stacked 2 deep in each hole to hold the nozzle into the spindle mount. This adapter was designed to be used with an Atrix Omega Supreme HEPA Vacuum Clean Room Fine Particle Vac. I imagine other vaccums…
The suction cup mounting screw broke on our Ken-Tech shower clock (https://www.amazon.com/dp/B001KA94T2) the clock still worked, but didn't have an easy way to use it since it won't sit upright by itself without the suction cup mount.…
Clips for holding a glass sheet on the Printrbot. Instructions Print off 4 clips, these were designed to work with the heat bed on a Printrbot+ with an 8" square 1/8 sheet of borosilicate glass from McMaster-Carr. The print had some…
I have an several times over upgraded original Printrbot Plus that's roughly equivalent to the Printrbot Plus v2.1, or 1306. I wanted to add a Geared v2 extruder to the printer but the only mounting kit for it was a laser cut plywood kit…
This is a case I created for the SainSmart BT to Serial Port module. This was printed on a Tiko in Gem PLA Category: Electronics
I've got a Printrbot+ 2.0 with, well I'm not sure which version of the extruder mount I have. The fan mount that came with it left a lot to be desired, and ended up cooling too much of the parts I was printing at a go so I put this duct…
Bracket for mounting an optical Z-endstop on the Printrbot Plus v2.0 using the mounting holes for the mechanical switch endstop. Instructions 3 perimeters, 40% infill I picked up the optical sensor from Amazon…
I wanted to add some rubber feet to my Printrbot Plus to give some more vibration dampening as I could hear the printer running all over the house through the vibrations on the table it's sitting on. This uses 16mm diameter self adhesive…
To wszystkie aktualnie dostępne wyniki.
