Liczymy pasujące modele…
The Slightly Over Engineered gang of garbage bag holders might be nicer but this one is mine. Two 60 mm holes. Select 0.4 or 0.6 mm version based on your nozzle. Throw it into slicer. Set one or two perimeters and 20 % infill. Print.
I've created variants for 0.2 and 0.3 mm layer height. 0.2 mm version is sliced at 3.22 grams. 0.3 mm version is sliced at 4.06 grams. The original BridgingTestMaterialSaving.3mf is sliced at 5.47 grams. There are four layers above the…
I've added a slight 1500 mm radius to create some preload. The snap-latch is now also preloaded more. Also the print in place hinge was tweaked. It is now hopefully easier to print - but I must admit I do not recall problems with previous…
For any thermistor with 3 mm diameter cartridge. Assembly: Print it Cut out the thin section acting as a support (circled in one of the images) Get thermistor wire through newly created crevice Pull the wire further so that thermistor…
2x1 Gridfinity container for six pcs of 18650 batteries.
This upgrade uses wobbleX in the intended way, unlike the version in the WobbleX Git repository and here on Printables. Simple 1:1 swap with the pre-tension nut V-Minion comes with. Note that this is not a miracle wobbly boi and you will…
In order to accomodate the brush and a dustpan, my solution was to rotate the broomholder and add a hook. Mounts to two 4mm countersink screws (with 7-8mm heads). Also the gear is now full.
Remix of 0ndsk4's Carbon filter for V-Core with enhanced exhaust geometry. Posted here with permission of author. Exhaust now blows air more sideways so bed is not cooled from below. Exhaust angle is not changed, only position. Basket…
After “upgrading” the KP3S PRO printer with Y axis with linear rails, I found that the previous screw was short and the screw delivered did not work with the spring. This print will enable the original screw to function. There is a 0,2 mm…
This is my Z-extrusion cap holding BTT SFS as well as bearing for Z-lead screw necessary for WobbleX. WobbleX cap uses 608 bearing. It should be possible to possible to install using light-medium force. The lead screw included in RR…
Printed in PETG. The fit allowed me to assemble by hand but the fit is strong enough that holding one watch allows raising the entire assembly. standur-filled-v1.stl is unchanged. You can see the change on the root of watch-mount-v3.stl.
The Kingroon Z homing screw was too long and I could not screw it in enough to have good first layer. Replace Kingroon screw with any M4 ISO 4762 Socket head screw. M4x16 should be best but beware - it was quite a challenge to get it…
I really liked MFBS's toolhead in my V-Core so I thought this excellent design would fare well on V-Minion as well. We can now enjoy excellent mix of rigidity and weight on cartesian as well. The STEP file contains multiple files and two…
It is the same as the original piece but with bottom pins replaced by holes. The idea is to stick a skewer (with glue or some rolled paper if scaled) there to have a deeper connection with the ground. Now also avaliable in STEP for easier…
Allows to use tensioner-less toolhead on V-Minion. M6 bolt with nut in printed piece moves the printed part to tension the belt. The original bolts are then tightened to hold position.
I had problem with filament sensor always detecting filament. Some fix it by filing down the lever and this is the other way - put a spacer between extruder body and the sensor, thus raising the gate up a bit. The fix is best done with…
This uses Noctua's fan duct geometry https://www.printables.com/model/887071-nv-aa1-12-airflow-amplifier which is attached to frame and pointed at bed. Duct is cut so that full bed travel is not limited. The lower the fan is the better -…
To wszystkie aktualnie dostępne wyniki.
