Liczymy pasujące modele…
I really like the original design by Simomura, but found that I couldn't see the top lights of the Google Home Mini when interacting with it. My Home Mini sits by the TV and the angle of the R2D2 pointed the lights away from my viewing…
An N-scale version of the HO-scale distribution center crafted by Kabrumble. I started designing it shortly after Kabrumble posted his file many months ago, then forgot all about it until another modeller ( jeff_j3ffr3y) posted their…
This is a building I designed for a small shop+office building for my train layout. The building and windows should print fine in the orientation shown. You might need supports for the building window openings, depending on your printer.…
Some basic guard rails for putting along your n-scale (1:160) roads. The design intent is that the designs meet at a post, for a better glue-up, but a little bit of easy filing seems to be needed at these fine scales to get a good match.…
Use this bridge set to have a highway overpass above your trains. The "short" piece can be used as is, and the longer piece is designed to that multiples can be glued together. In the pictures above, the long bridge is two pieces…
I have a future scene on my lower level that is a single track siding. I stumbled on this cement industry siding on Google Maps in Oregon. I used TinkerCad to design the pieces. My goal with this project was to see if I could print a…
Building I designed for a small non-railroad industry on my train layout. The building and windows should print fine in the orientation shown. You might need supports for the building window openings, depending on your printer. I have…
HO Rerailer for model trains, modelled after the Rix Products design. Includes a few minor supports to avoid having to support the entire ramp when printing. These supports should just snap off when the print is complete. Measuring 29cm…
Pier walls to help create a dock or marina scene on your train layout or other model work. The design was modeled after a similar resin product that was too tall (you can see it in the bottom left of the image) Print instructions…
Two sizes of lumber loads for 61' and 73' N-scale centerbeam/spline rail cars. Also included are templates for cutting out the paper "load-covers" that get wrapped around the printed block. (Don't cut out the middle rectangle - it's just…
A chemical facility that I'll eventually use on my N scale layout. I have not yet printed this structure, but I don't suspect it will have any troubles. Supports are likely required for the large window spans of the main building. The…
This is a really fine track bumper for N-scale model railroads. It's measurements are based on the Walthers model that is commercially available. I suggest printing on a resin printer. Included is an STL file of 10 bumpers with supports…
Needed a display for the Marvel Hero's branded golf balls. Decided to create versions that hold 1 to 6 balls. You can use the single ones for display your "Hole in One" ball, or any other special occasion ball. Category: Sport & Outdoors
A representation of the Toronto Union Station Shed in N-scale (1:160), to span 4 pairs of tracks in a station yard. All of the parts in the two "ALL" STL files are required to do two rows of the shed. Repeat as desired based on the length…
I had punched out the wrong hole on an electrical handy-man box and needed to cover it up. Found the original design by Apappano but closed it up to form a cover instead of a bushing. Worked great on the first try. Print instructions…
An approximate model of CN/CP snow / rock sheds found in the Thompson River Canyon, in Canada. Category: Buildings & Structures
Quick model of an N Scale Girder Bridge, based loosely on the similar Micro Engineering bridge. For FDM Printing, you'll need to print: 2 x sides 2 x braces, 6-7 x cross members. If you have a resin printer, I've had good success printing…
Building I designed for a small non-railroad industry on my train layout. The building and windows should print fine in the orientation shown. You might need supports for the building window openings, depending on your printer. You can…
A small clip to use when mounting PCBs to your project board. Print it on it's side to avoid needing supports. 100 clips will easily fit on a 200x200 print bed. Print instructions Category: Electronics
I liked the original project ( https://www.thingiverse.com/thing:4748009 ) and felt it was a good fit for an area I was about to design a new building for. I scaled the design files to fit N-scale (54%), and pre-assembled the walls and…
A few replacement parts for DEERC 300e / 9300e RC 1:18 vehicles. Will likely also work with Sandy Land vehicles, as they share many of the same underpinnings. If/when other parts break, if I design a fix, I will continue to add to this…
Building I designed for a small non-railroad industry on my train layout. The building and windows should print fine in the orientation shown. You might need supports for the building window openings, depending on your printer. You can…
A representation of the Toronto Union Station Shed in N-scale (1:160), to span pairs of tracks in a station yard. These were designed to print as one piece, and sized for an Elegoo Saturn 8K printer. I'm sure it'll work on most printers…
When setting up the enclosure for my AnyCubic Photon S printer, I needed a way to ventilate to the outside, and needed to run about 50' around the basement to get there. 1.5" ABS plumbing pipe is fairly cheap and easy to setup. Any…
Tired of knocking over your decal setting solutions? Here's a holder to keep them safe, plus a little water tray to soak your decals in. 2 bottle and 3 bottle versions included. Category: Hobby
Anker Qi stand that I deisgned for the iPhone 8 but I imagine it will work well with other phones of similar dimensions and charging placement. Angled such that it allows the screen to be visible while charging. The Qi cable stays hidden…
A mount for installed LED lights into the HO-Scale and N-Scale Walthers Roundhouse kit. It press fits onto the roof support beams. A dab of glue couldn't hurt too! Works with LEDs from eBay with description: L3528r Pre Wired SMD 3528 --…
Replacement bridge pier footings, modelled to resemble those supplied with N-Scale Micro Engineering Trestle piers. I've printed them on both filament and resin printers with good results. Category: Buildings & Structures
We're having a Foosball tournament at work, so I used this Ironman design as the basis for a pair of trophies that will go to the winning team. Pieces were printed in translucent white PLA, with the layers in front the LEDs about 0.7mm…
This is a remix of two great products: Mx SMD component strip holder https://www.thingiverse.com/thing:2186862 SMD Strip Dispenser Tray for Mx SMD Roll https://www.thingiverse.com/thing:2717152 I was really impressed by how these two…
I wanted to be able to change the pivot/spin direction of my Honeywell Turboforce HT-900 fan after it was mount on the wall. Between this spin and the normal tilt of the original fan, I can point the airflow in almost any direction. I…
Simple clip to help keep cables aligned in your Digitrax power center. While hold 4 cables, screw in place. Print instructions Unassociated tags: db 220, dcs 240 Category: Electronics
A heavy remix of the design from Nepav - I really only kept his angled arms for the camera portion, and kept similar arm "widths". I like the ideas of the original model, and how it match the aesthetics of the S1 printers. However, it…
A clip that will slide onto your Digitrax DCS 240 or DB 220 to keep your cables nice and organized. Will hold the three cables coming out the front of your booster. (I'm not sure if it will fit the older Digitrax boosters - I think they…
Replacement pivot slider for Tortoise by Circuitron slow motion motors. Print instructions Category: Hobby Print Settings Printer: JG Aurora A3 Rafts: No Supports: No Resolution: 0.1mm height Infill: 20%
I really like the design and airflow that I got from the original part, version 2: https://www.thingiverse.com/thing:3943491 However, I found the mount to be really weak and wobbly. The slot holes don't leave much material at the top and…
Decided to add a glass plate to the heatbed, but the limit switch was too low. Crafted this adapter that matches the thickness of the glass I used (from a cheap picture frame). Re-uses the existing screw of the Z-axes motor mount/bearing…
To wszystkie aktualnie dostępne wyniki.
