Liczymy pasujące modele…
Updates: 2026-10-07 Updated V2 for much easier priming. 2026-09-24 Added 3 V2 variants that print without support. 2026-07-05 Added a version with looser barrel fit. 2026-07-03 Added a version with looser clip; print this if you think the…
It's a simple drop-in replacement for the rev trigger. I find it annoying to mis-press the rev trigger so easily, so I made this. It still allows the player to use the main trigger as a 2-stage trigger.
Recommend printing with PETG / PLA tough variants.
Updates 2026-06-10 Add a larger version of battery door (as shown in the 3rd pic) Key Features Expanded Battery Bay: Fits larger batteries, specifically optimized for the Tattu 650mAh 3S LiPo (16mm x 29mm x 56mm) and similarly sized…
A drop-in replacement for the rev trigger, which adds 2-stage trigger feature to your vecto pro. Two versions available: Dual-purpose: Add a 2-stage trigger feature while keeping the rev trigger. Rev trigger delete: Add a 2-stage trigger…
2026-07-10 update: Added a v3, which extended the locking slot a bit; hopefully it can fit more stocks. 2026-07-09 update: Added a v2, which support using the original screw to screw-in from the other side, and have a tighter fit at the…
It's my version of stackable block pier
How to use: Print the mold in PETG or other filaments that can withstand 70 degree temperature. Put darts in; the dart tail goes in. You may spin the darts to make them easier to go in. Put the loaded mold into the filament dryer, set to…
Update: 2026-09-27 Added a v2 with a better fit that doesn't jam darts as easily. Print with PETG or PLA tough, or it may snap when installing. To install, remove the base plate and clip in the extender from the side.
This barrel is NOT TESTED YET. For some reason, I have the long barrel, but not the blaster. Based on my successful experience with a tight bore barrel with 40max lightning, I made this barrel to boost accuracy. This can be screw in from…
With this stock, it won't 100% collapse; it would friction-fit at around 90% collapsed, thus the top button won't be needed. To print with minimum support, print with this orientation: The trade-off is that the buttplate finish would be…
No hardware required, just keep using the original spring. It's friction-fitted; tapes can be wrapped before installing if it's not tight enough. Please note that the installation direction matters; the smaller groove inside should face…
Compatible with DZ straight talon mag. For curved mag, it probably fit too, not tested though.
The official BCAR barrel doesn't work well with used darts, so I made this. If you have GFZ BCAR already, you may skip this, because that's probably a superior option. This is simply a narrow bore barrel (around 14mm after shrinking) that…
Not a fan of the pink mag release, so I make one to print in other color. Also make a pull mag release delete.
Clip in from the right-hand side.
I integrated a pic rail clamp to it. It can friction-fit quite well (if you prime it before attaching it), and use M4 screws and nuts. It is the left shell, print every other parts from the original.
Add 2 more rounds to your lightningale mag! Remove the original base plate , then install this. Remarks: It's not compatible with original lightning mag.
2026-06-23: Added v2: slightly less tight fit with the blaster, and better fit on the belt clip. PETG or PLA tough variant recommended
Updates Date updates 2026-08-30 Add a new version of the stock door and lock piece to enable flick-open (Please read the folding stock section below) 2026-08-25 Updated flywheel, please use with caution and read the flywheel session below…
To wszystkie aktualnie dostępne wyniki.
