P
PrintablesCostal Radio
Drone Pilot Wings
Do you fly a drone? Do you want the respect you deserve? Too bad. But, you can print yourself some cute little pilot wings.
- Pobrania
- 137
- Polubienia
- 22
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesCostal Radio
FT-817/818 Protection Rails
This is a remix of Maker222b's "FT817/818/ND protection frame" on Thingiverse. I rounded and chamfered edges and corners, added an extra 50mm to the back to create room for cables, and added holes for threaded inserts. The intent is to…
- Pobrania
- 44
- Polubienia
- 2
- Ocena
- 0
P
PrintablesCostal Radio
14MHz (20m band) Coil for Gabil 50" Whip
This is an improved version of my 20m loading coil for Gabil 50" whip. It should be MUCH easier to actually make. This print should work on most printers without needing support material (all overhangs kept to 45 degrees). PETG…
- Pobrania
- 29
- Polubienia
- 7
- Ocena
- 0
P
PrintablesCostal Radio
7MHz (40m band) Coil for Gabil 50" Whip
This is an improved version of my 40m loading coil for Gabil 50" whip. It should be MUCH easier to actually make. This print should work on most printers without needing support material (all overhangs kept to 45 degrees). PETG…
- Pobrania
- 29
- Polubienia
- 5
- Ocena
- 0
P
PrintablesCostal Radio
10MHz (30m band) Coil for Gabil 50" Whip
This is an improved version of my 30m loading coil for Gabil 50" whip. It should be MUCH easier to actually make. This print should work on most printers without needing support material (all overhangs kept to 45 degrees). PETG…
- Pobrania
- 18
- Polubienia
- 5
- Ocena
- 0
P
PrintablesCostal Radio
BNC Transformer Spacer
Disclaimer: I have no affiliation with Adam Kimmerly (K6ARK). I just like his stuff, and his kits were out of stock, so I made this. You should check out his stuff if you haven't. For this transformer, you'll need: FT50-43 Ferrite Toroid…
- Pobrania
- 15
- Polubienia
- 1
- Ocena
- 0
P
PrintablesCostal Radio
Chest Carrier for Yaesu FTM-150R
The Yaesu FTM-150R(ASP) is a pretty good radio for working FM repeater satellites. It is able to do crossband duplex, has good harmonic filtering, and has a good receiver. It is a bit clunky to use with a handheld beam antenna (Arrow or…
- Pobrania
- 14
- Polubienia
- 6
- Ocena
- 0
P
PrintablesCostal Radio
Tiny Paddle Adapter for UV-K5
Shut up and listen! Here is what you are going to do. Go to Amazon and buy a Quansheng UV-K5. Go to N6ARA Electronics buy: Tiny Paddle N6ARA TinyPaddle – Plug – Assembled – N6ARA (you can also get as a kit if you prefer) Tiny Filter…
- Pobrania
- 14
- Polubienia
- 2
- Ocena
- 0
P
PrintablesCostal Radio
Elecraft KH1 Magsafe Mount
PETG Recommended Print on edge to allow for maximum strength when clipping and unclipping. It prints without supports. Make sure your print bed is CLEAN, there is not a lot of contact area on the first layer. If it struggles to print, use…
- Pobrania
- 13
- Polubienia
- 5
- Ocena
- 5
P
PrintablesCostal Radio
MFJ-939 Protective Rail
A set of rails to protect the buttons and connectors on an MFJ-939 tuner. You can either print each rail as a single piece (if your printer is big enough), or you can print the front and back half separate and join with the bracket and…
- Pobrania
- 12
- Polubienia
- 1
- Ocena
- 0
P
PrintablesCostal Radio
TalentCell 3000mAh Switch Cover
Protective cover to prevent the switch on your TalentCell 3000mAh from getting flipped in your bag. PETG recommended.
- Pobrania
- 8
- Polubienia
- 1
- Ocena
- 0
P
PrintablesCostal Radio
K6ARK Pico Paddle Mount for Quansheng UV-K5
If you are interested in doing 2m or 70cm CW, you should look into the NR7Y custom firmware for the Quansheng UK-K5/K1 ( CW Firmware Docs - NR7Y CW Firmware Docs ). There are ways to use it with and without opening and modifying the…
- Pobrania
- 0
- Polubienia
- 3
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.