Liczymy pasujące modele…
Yet another pool bridge replacement. Designed to replace broken one with strength in mind. Mounting dimensions: - total length: 30mm - deeper part diameter: 9.5mm - deeper part length: up to 15mm - shallower part diameter: 13.2mm -…
My wife needed some tool to measure/mark curves when working with sewing stencils/cutting fabrics… So here it is :) For brave people: print box horizontally and use nice infill pattern on top ;) PS: This time no model file… It is my first…
I needed stand for quite heavy microphone (PC microphone by Tracer with fancy “cage” suspension). It has 6mm wide tab with a hole that accommodates M5 screw - so it was chosen as stand's “interface”. FreeCAD project file is included so if…
If printed as a whole part, supports on the bed are required. It may be cut at 2mm height to separate riser and top part as in original model.
Cue clip & rest meant as an extension to existing cue rack. Mounting footprint 32x32mm. Mounting: two 2x10mm screws for clip two 3x30 + 3x20mm Printing: Nozzle: 0.4mm or larger (I've printed with 0.6mm) Layer height: 0.2-0.3mm Material:…
Original packing of IKEA Måla pens is not intended for storage so I designed (and printed) one :) “Standard” settings should be OK (I've printed in PLA with layer 0.3, two perimeters, infill isn't critical), probably 0.6 nozzle will work…
Both parts require supports, PETG highly suggested. Upper PSU holder of own design, AlternativeSupplyCover is remix of original one.
All the four pads are very same. Print with TPU, additional perimeters recommended.
It is quite common pattern for PP/PE boxes to have “hinges” made as bending strips. Over the time, they tend to break, often rendering box unusable. As this time box was dedicated to some electronic device and replacement one was not…
Almost any material will do the job - I've printed mine with DevilDesign Matt PLA
Just rubber pads for LÄTTHET regulated feet - marked as v2, because have 0.5mm deeper central part to better support feet (central bump is a bit higher than a rim, making feet less stable on hard surfaces). It looks it should also fit…
What to do, when original cue holder breaks? Print a new one! This is replacement clip for popular cue holders with clips mounted in routed groove and a single mounting screw per clip. Hard TPU preferred, PP would also work well.
Small switches are convenient to be mounted under the desk, but not all have reliable mount holes. More over, Cisco ones have vents of the box, so we don't want to cover them. PLA works just well, if you are afraid of the temperature, use…
Print with TPU, no special dimensional accuracy required, so 0.6 nozzle with SPEED/DRAFT settings would be OK. For best result print with supports, round part upwards.
Handlebar 25.5mm, mount hole 27mm (FreeCAD model included). Will require four M5 bolts (~40mm long) and “standard”nuts (self-locking nuts recommended). I've printed with Devil Design ASA with .4 nozzle, 4 perimeters, 25% infill for better…
Most "dust filter" designs can't accommodate PC4 (bowden tube) connectors. It may be an issue, especially when working with Prusa MMU2 unit and "self rewinding" spool holders. In additional my spool holders are a bit taller than usual (to…
Mounting bracket for FTM-350 amateur TRX - i.e. for under-shelf mounting. TRX unit is secured with 4 screws (knobs are prepared for M4x16mm ones). Bracket has place for 5 mounting screws (countersunk head, up to 4mm, but can be drilled…
Simple box for switches to turn enclosure lights on and off. Print instructions Just print, cut window at the bottom of plexi panel (60mm height, 80mm width) and insert. Use two holes in bottom part to fix it to lower table (3x25mm screws…
"Well known" self-rewinding spool holders have longer axle than those used by MMU2/S ones (also employed in Lack Enclosure v2 5-spool stand). So we may shorten spool hub (and gave problems with some wider spools), use original stands from…
Simple stand for docking station, making connecting USB devices (like U2F keys) easier.
Simple box for switches, with connectors for common peripherals and some room for power supply for LED stripes. IEC C14 for power input IEC C13 power outlet for printer “Standard” AC outlet for supply for Raspberry Pi Round DC connector…
Replacement spool core (hub) for https://www.thingiverse.com/thing:3392240 (Fiberlogy refills were a bit too tight for original one). Screw & nut required, as core is not as tight fit into spool sides as original core. Print instructions…
Simple strap to mount electrical junction box on wire fence (but may have other uses).
IKEA KOMPLEMENT shoe racks have one flaw - they are bolted with three long screws with plastic spacer between sliding rail and the cabinet, which (especially with "lazy minors use") tend to be ripped-off the holes. This version is…
To wszystkie aktualnie dostępne wyniki.
