Liczymy pasujące modele…
Most XT30 housings on Printables are designed for bulky RC/drone battery leads, typically using 14–16 AWG silicone wire for relatively high-current RC/drone applications. I needed a connector housing for a much thinner cable — an aquarium…
Have you ever noticed that tiny particles and dust contaminate in your backpack? Its come from your pencils, crayons, booklets and other artifacts or from environment e.g. plants, animals. You can turn your backpack inside out or open the…
This is a storage case for the interchangeable dies of a crimping tool. It prints in one piece with no supports required. After printing, the hinges may be slightly tight at first, but they loosen up and move smoothly after a few…
It is designed to hang directly on a wall outlet, providing a convenient shelf for your phone while it charges. The shelf and hook should ideally be 3D-printed from ABS or PETG, while the rubber ring and anti-slip pads are best made from…
Universal hook for Biltema / Angel-Cache fishing rods. Unlike standard screw-in or glued hooks, it requires no modification of the rod. It is intended for a 7–8 m carbon-fibre telescopic fishing rod with the last segment removed. The hook…
The detailed description can be found here: https://motleyscience.com/2025/11/22/portable-moxon-antenna-for-weather-radiosonde-hunting/
This is a custom-designed 3D-printed enclosure for the MySondy Go radiosonde hunting device based on the TTGO LoRa32. The housing is optimised for outdoor, real-world use: it protects the electronics from dust while keeping all essential…
This is a 3D-printed lottery ticket scratcher designed to fit on a key ring. Its smooth plastic edge is less likely to damage the printed numbers or barcode than using a coin. A fun, quirky gift for lottery enthusiasts. PETG recommended…
The Gauss Howitzer is an educational magnetic accelerator designed to demonstrate fundamental physics concepts—most notably the law of conservation of momentum. It is not a weapon, but a tabletop learning tool that visually illustrates…
This 3D-printable antenna hub and accessory set lets you build a cost-effective, portable quarter-wave ground plane antenna ideal for airband listening. The central hub houses a BNC connector and supports the monopole and radial elements,…
This project adapts a KKmoon digital frequency counter module for use with a classic Grundig GDO 701. The module is specified for 1–500 MHz, but it can be used up to about 1.1 GHz. Accuracy is high below 500 MHz; above 500 MHz, readings…
First, I designed a simple hook that can be mounted to various surfaces using 19 mm wide double-sided tape. Then, I created a safety version of it, featuring a small latch that prevents the hung object from accidentally falling off. Both…
Two replacement foot plugs for aluminium household ladders (e.g., Krause and similar): one for 40×20 mm legs and one for 33×20 mm legs. Print the plugs in ABS or PETG. The soles can be printed in TPU with 100% infill, or cut from a rubber…
A small 3D-printed upgrade kit for the NZ-1 hand winding machine. The original machine uses an M10 threaded shaft with simple plastic cones, which makes it difficult to clamp smaller coil formers securely. This modification adds a rigid…
This Chaotic Pendulum Hand Spinner is a compact, hand-held physics toy that demonstrates chaotic motion in an intuitive and playful way. By combining rotational motion with an offset pendulum mass, the spinner produces complex,…
A pole-mounted line cutter for radiosonde recovery. The tool attaches to the tip of a telescopic fishing pole and helps pull, guide, or cut the line, parachute cord, or balloon remnant when a radiosonde is caught in a tree or other…
This is a lightweight, foldable mushroom-picking basket designed to fit into a backpack when not in use. It is meant for short foraging trips where a full-size wicker basket would be inconvenient, especially if you end up finding no…
I bought a Küchenprofi Tea Timer set (see: https://www.kuchenprofiusa.com/products/kuchenprofi-tea-timer-sand-set ). The hourglasses are really nice, but the manufacturer doesn’t provide a stand for them, so they tend to roll around…
Description This enclosure was designed for my 30 MHz–1.3 GHz, 1:1000 frequency counter prescaler , which extends the useful range of older frequency counters into the VHF and UHF bands. The case consists of two parts: a bottom housing…
To wszystkie aktualnie dostępne wyniki.
