P
PrintablesLabrat
Adhesive kitchen hooks
Simple adhesive hooks for utensils to be glued (or acrylic-taped) onto the underside of a kitchen cupboard.
- Pobrania
- 514
- Polubienia
- 83
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesLabrat
3.5" HDD shock absorbing sealable box
6x M3x25mm screws are required for assembly. Print inlays and ring seal in TPU . The seal is best printed in 100% infill - concentric. For the inlays, use 2-4 walls and no more than 0.8 mm top surface thickness. Use 5-8% infill for harder…
- Pobrania
- 244
- Polubienia
- 54
- Ocena
- 5
P
PrintablesLabrat
Tableside shelf
If there is not enough place on the table.
- Pobrania
- 224
- Polubienia
- 39
- Ocena
- 5
P
PrintablesLabrat
2x2 Eppendorf tube racks
After seeing my colleagues melting a couple of these racks printed in PETG by locating them in a 95 degree thermostat, I've also added a version with easily readable maximum temperature label. Printing parameters for the nice finish:…
- Pobrania
- 202
- Polubienia
- 13
- Ocena
- 5
P
PrintablesLabrat
Cold Steel bokken replacement tsuba (handguard)
Original tsubas on the Cold Steel Bokken are thin and made of injection-molded polypropylene with very high glass fiber content. This makes them rather brittle and they tend to break during bokkendo sparring. The manufacturer sells no…
- Pobrania
- 141
- Polubienia
- 6
- Ocena
- 0
P
PrintablesLabrat
GL45 cap for rubber stoppers
Smaller diameter hole compared to original red Duran caps prevents damage to the edge of the stopper. I've redesigned the cap with medium pressure (2-4 bar) and autoclavability in mind. I've increased the thickness of the upper flat part…
- Pobrania
- 139
- Polubienia
- 2
- Ocena
- 0
P
PrintablesLabrat
Stitching thread organizer
A simple thread organizer for stitching, 20 holes
- Pobrania
- 71
- Polubienia
- 10
- Ocena
- 0
P
PrintablesLabrat
Lightweight 50mL Falcon tubes rack - 100g of filament only
There are two versions of the rack: with a "MAX 65°C" reminder text embossed in the wall (intended to be printed in PETG) and a version without any text. Line width: 0.5 mm (the walls of the model are exactly 1 mm thick). Layer thickness:…
- Pobrania
- 66
- Polubienia
- 6
- Ocena
- 0
P
PrintablesLabrat
Epifluorescent microscopy slide with vats
Designed in the size of a standard microscopy slide. Side channel in each vat was designed for air bubble removal and dye solution top up. For use with 17x17 mm cover glass. Recommended printing material: Black PETG.
- Pobrania
- 18
- Polubienia
- 2
- Ocena
- 0
P
PrintablesLabrat
OrangePi Lite stand for RPi mounting holes
Stand holes spacing: 42 x 63 mm Baseplate holes spacing: 49 x 58 mm Screws size: M3x[5-12] for the board stands, M3 of the applicable length and M3 nuts for the baseplate. Filament: any common filament will do. PETG stands can be threaded…
- Pobrania
- 14
- Polubienia
- 4
- Ocena
- 0
P
PrintablesLabrat
35mm large diameter lock-on grips
Printing material: TPU/TPE. Tested with both 95A and 83A. Number of perimeters: 2 for soft grips, 4-5 for hard grips. Layer thickness: 0.1 - 0.2 mm Infill: gyroid, 8-30% depending on the desired hardness. Supports: Snug, from the printbed…
- Pobrania
- 13
- Polubienia
- 11
- Ocena
- 0
P
PrintablesLabrat
Vibration-dampening feet for a floor fan
Material: TPU/TPE. Number of perimeters: 1-3 (for TPU A95) or 2-4 (for softer filaments). For optimal performance, for the "Side feet" model, use 1-2 perimeters up to 18 mm height and 3-6 perimeters above 18 mm. Top layers: at least 5 (1…
- Pobrania
- 7
- Polubienia
- 3
- Ocena
- 5
P
PrintablesLabrat
Sigma Curve rear light ziptie adapter
Filament: tested with PCTG and PETG. Likely, any non-flexible filaments will do. Tested with the Sigma Curve model. Two adapters required for assembly. Zipties: maximum width 5 mm; 4 pcs.
- Pobrania
- 4
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.